A new approach for reverse analyses in depth-sensing indentation using numerical simulation
Autor(a) principal: | |
---|---|
Data de Publicação: | 2007 |
Outros Autores: | , , |
Tipo de documento: | Artigo |
Idioma: | eng |
Título da fonte: | Repositório Científico de Acesso Aberto de Portugal (Repositórios Cientìficos) |
Texto Completo: | http://hdl.handle.net/10316/4212 https://doi.org/10.1016/j.actamat.2006.08.019 |
Resumo: | This paper seeks to present a new approach to reverse analysis in depth-sensing indentation which makes use of numerical simulation. This methodology allows the results of experimental hardness tests acquired with single indenter geometry to be used to determine the plastic properties of materials. Forward and reverse analyses of high deformation three-dimensional numerical simulations of Vickers indentation tests are used to determine different mechanical properties of materials: Young's modulus, yield stress and strain-hardening exponent. The Vickers indenter used in the numerical simulations is formulated as a rigid body and takes into account the presence of the most common imperfection of the tip, so-called offset. The contact friction between the Vickers indenter and the deformable body is also considered. The forward analysis uses materials with Young's modulus values from 50 to 600 GPa, yield stress values from 0.3 to 10 GPa and strain-hardening exponents from 0 to 0.6; the Poisson ratio did not vary from 0.3. The representative plastic strain [epsilon]r and the correspondent stress [sigma]r, as previously defined by other authors [Dao M, Chollacoop N, Vliet KJ, Venkatesh TA, Suresh S. Acta Mater 2001;49:3899], were identified by an independent numerical method. The values of the representative plastic strain [epsilon]r obtained for the Vickers indenter confirm those of the above-mentioned authors, despite showing a slight influence from the Young's modulus values. The forward study enables the production of a unique plot of the hardness HIT vs. representative stress [sigma]r, where both are normalized by the Young's modulus E. The proposed reverse analysis provides a unique solution to the representative stress [sigma]r and the strain-hardening exponent, n, given that the Young's modulus is predetermined from the experimental hardness test. Depending on the material properties, the value of n can be more or less sensitive to the scatter of the experimental results obtained using the depth-sensing equipment, particularly the stiffness of the unloading curve. The validity of the proposed reverse analysis method is checked using three real materials: stamping quality steel (DC 06), stainless AISI 304 steel and BK7 glass. |
id |
RCAP_1a43016f96ae94b4ceb660faf66a0c53 |
---|---|
oai_identifier_str |
oai:estudogeral.uc.pt:10316/4212 |
network_acronym_str |
RCAP |
network_name_str |
Repositório Científico de Acesso Aberto de Portugal (Repositórios Cientìficos) |
repository_id_str |
7160 |
spelling |
A new approach for reverse analyses in depth-sensing indentation using numerical simulationReverse analysisNanoindentationVickers indenterThis paper seeks to present a new approach to reverse analysis in depth-sensing indentation which makes use of numerical simulation. This methodology allows the results of experimental hardness tests acquired with single indenter geometry to be used to determine the plastic properties of materials. Forward and reverse analyses of high deformation three-dimensional numerical simulations of Vickers indentation tests are used to determine different mechanical properties of materials: Young's modulus, yield stress and strain-hardening exponent. The Vickers indenter used in the numerical simulations is formulated as a rigid body and takes into account the presence of the most common imperfection of the tip, so-called offset. The contact friction between the Vickers indenter and the deformable body is also considered. The forward analysis uses materials with Young's modulus values from 50 to 600 GPa, yield stress values from 0.3 to 10 GPa and strain-hardening exponents from 0 to 0.6; the Poisson ratio did not vary from 0.3. The representative plastic strain [epsilon]r and the correspondent stress [sigma]r, as previously defined by other authors [Dao M, Chollacoop N, Vliet KJ, Venkatesh TA, Suresh S. Acta Mater 2001;49:3899], were identified by an independent numerical method. The values of the representative plastic strain [epsilon]r obtained for the Vickers indenter confirm those of the above-mentioned authors, despite showing a slight influence from the Young's modulus values. The forward study enables the production of a unique plot of the hardness HIT vs. representative stress [sigma]r, where both are normalized by the Young's modulus E. The proposed reverse analysis provides a unique solution to the representative stress [sigma]r and the strain-hardening exponent, n, given that the Young's modulus is predetermined from the experimental hardness test. Depending on the material properties, the value of n can be more or less sensitive to the scatter of the experimental results obtained using the depth-sensing equipment, particularly the stiffness of the unloading curve. The validity of the proposed reverse analysis method is checked using three real materials: stamping quality steel (DC 06), stainless AISI 304 steel and BK7 glass.http://www.sciencedirect.com/science/article/B6TW8-4M69JXG-1/1/ffe1726f3b7df73e4e01c941d6c4cbef2007info:eu-repo/semantics/publishedVersioninfo:eu-repo/semantics/articleaplication/PDFhttp://hdl.handle.net/10316/4212http://hdl.handle.net/10316/4212https://doi.org/10.1016/j.actamat.2006.08.019engActa Materialia. 55:1 (2007) 69-81Antunes, J. M.Fernandes, J. V.Menezes, L. F.Chaparro, B. M.info:eu-repo/semantics/openAccessreponame:Repositório Científico de Acesso Aberto de Portugal (Repositórios Cientìficos)instname:Agência para a Sociedade do Conhecimento (UMIC) - FCT - Sociedade da Informaçãoinstacron:RCAAP2020-11-06T16:48:44Zoai:estudogeral.uc.pt:10316/4212Portal AgregadorONGhttps://www.rcaap.pt/oai/openaireopendoar:71602024-03-19T20:58:31.940925Repositório Científico de Acesso Aberto de Portugal (Repositórios Cientìficos) - Agência para a Sociedade do Conhecimento (UMIC) - FCT - Sociedade da Informaçãofalse |
dc.title.none.fl_str_mv |
A new approach for reverse analyses in depth-sensing indentation using numerical simulation |
title |
A new approach for reverse analyses in depth-sensing indentation using numerical simulation |
spellingShingle |
A new approach for reverse analyses in depth-sensing indentation using numerical simulation Antunes, J. M. Reverse analysis Nanoindentation Vickers indenter |
title_short |
A new approach for reverse analyses in depth-sensing indentation using numerical simulation |
title_full |
A new approach for reverse analyses in depth-sensing indentation using numerical simulation |
title_fullStr |
A new approach for reverse analyses in depth-sensing indentation using numerical simulation |
title_full_unstemmed |
A new approach for reverse analyses in depth-sensing indentation using numerical simulation |
title_sort |
A new approach for reverse analyses in depth-sensing indentation using numerical simulation |
author |
Antunes, J. M. |
author_facet |
Antunes, J. M. Fernandes, J. V. Menezes, L. F. Chaparro, B. M. |
author_role |
author |
author2 |
Fernandes, J. V. Menezes, L. F. Chaparro, B. M. |
author2_role |
author author author |
dc.contributor.author.fl_str_mv |
Antunes, J. M. Fernandes, J. V. Menezes, L. F. Chaparro, B. M. |
dc.subject.por.fl_str_mv |
Reverse analysis Nanoindentation Vickers indenter |
topic |
Reverse analysis Nanoindentation Vickers indenter |
description |
This paper seeks to present a new approach to reverse analysis in depth-sensing indentation which makes use of numerical simulation. This methodology allows the results of experimental hardness tests acquired with single indenter geometry to be used to determine the plastic properties of materials. Forward and reverse analyses of high deformation three-dimensional numerical simulations of Vickers indentation tests are used to determine different mechanical properties of materials: Young's modulus, yield stress and strain-hardening exponent. The Vickers indenter used in the numerical simulations is formulated as a rigid body and takes into account the presence of the most common imperfection of the tip, so-called offset. The contact friction between the Vickers indenter and the deformable body is also considered. The forward analysis uses materials with Young's modulus values from 50 to 600 GPa, yield stress values from 0.3 to 10 GPa and strain-hardening exponents from 0 to 0.6; the Poisson ratio did not vary from 0.3. The representative plastic strain [epsilon]r and the correspondent stress [sigma]r, as previously defined by other authors [Dao M, Chollacoop N, Vliet KJ, Venkatesh TA, Suresh S. Acta Mater 2001;49:3899], were identified by an independent numerical method. The values of the representative plastic strain [epsilon]r obtained for the Vickers indenter confirm those of the above-mentioned authors, despite showing a slight influence from the Young's modulus values. The forward study enables the production of a unique plot of the hardness HIT vs. representative stress [sigma]r, where both are normalized by the Young's modulus E. The proposed reverse analysis provides a unique solution to the representative stress [sigma]r and the strain-hardening exponent, n, given that the Young's modulus is predetermined from the experimental hardness test. Depending on the material properties, the value of n can be more or less sensitive to the scatter of the experimental results obtained using the depth-sensing equipment, particularly the stiffness of the unloading curve. The validity of the proposed reverse analysis method is checked using three real materials: stamping quality steel (DC 06), stainless AISI 304 steel and BK7 glass. |
publishDate |
2007 |
dc.date.none.fl_str_mv |
2007 |
dc.type.status.fl_str_mv |
info:eu-repo/semantics/publishedVersion |
dc.type.driver.fl_str_mv |
info:eu-repo/semantics/article |
format |
article |
status_str |
publishedVersion |
dc.identifier.uri.fl_str_mv |
http://hdl.handle.net/10316/4212 http://hdl.handle.net/10316/4212 https://doi.org/10.1016/j.actamat.2006.08.019 |
url |
http://hdl.handle.net/10316/4212 https://doi.org/10.1016/j.actamat.2006.08.019 |
dc.language.iso.fl_str_mv |
eng |
language |
eng |
dc.relation.none.fl_str_mv |
Acta Materialia. 55:1 (2007) 69-81 |
dc.rights.driver.fl_str_mv |
info:eu-repo/semantics/openAccess |
eu_rights_str_mv |
openAccess |
dc.format.none.fl_str_mv |
aplication/PDF |
dc.source.none.fl_str_mv |
reponame:Repositório Científico de Acesso Aberto de Portugal (Repositórios Cientìficos) instname:Agência para a Sociedade do Conhecimento (UMIC) - FCT - Sociedade da Informação instacron:RCAAP |
instname_str |
Agência para a Sociedade do Conhecimento (UMIC) - FCT - Sociedade da Informação |
instacron_str |
RCAAP |
institution |
RCAAP |
reponame_str |
Repositório Científico de Acesso Aberto de Portugal (Repositórios Cientìficos) |
collection |
Repositório Científico de Acesso Aberto de Portugal (Repositórios Cientìficos) |
repository.name.fl_str_mv |
Repositório Científico de Acesso Aberto de Portugal (Repositórios Cientìficos) - Agência para a Sociedade do Conhecimento (UMIC) - FCT - Sociedade da Informação |
repository.mail.fl_str_mv |
|
_version_ |
1799133876369489920 |