Seleção de parâmetros de soldagem a ponto por resistência, baseado na medição da resistência elétrica entre chapas

Detalhes bibliográficos
Autor(a) principal: Nascimento, Vinicius Castanheira do
Data de Publicação: 2008
Tipo de documento: Dissertação
Idioma: por
Título da fonte: Repositório Institucional da UFU
Texto Completo: https://repositorio.ufu.br/handle/123456789/14831
Resumo: Resistance Spot Welding applied in production lines may demand previous programming for welding parameter settings as a function of demanded sequential changes, due to as much as material type as thickness. In the case of a manual operation, the operator is the one in charge of changing the program when different welding conditions is identified in a same sequence of spots. Considering being an online operation, this is a potential source of error. Thus, the main motivation for this work was to verify the possibility of parameter regulation in a spot welding production line, based on measurement of the electrical resistance between the sheets. A series of experiments was carried out to verify the minimum number of cycles and the ideal electrical power needed to measure the electrical resistances between carbon steel and galvanized steel and between a different thickness sheets. The results showed that the electrical resistance can be determined from only six cycles and that it is possible to differentiate sheet combinations. They also reveal that the resistances variation amongst sheet combinations were repetitive and distinguished enough to claim the use of this principle to classify the material combinations by regions of electrical resistance, both by the difference in thickness and type of superficial coating. In this work, it was also defined the technique known as the Burn Zinc and presented an experimental procedure to achieve optimal parameters to use this technique.
id UFU_cfa33d8319eadeac1bf6e355d3c91cdf
oai_identifier_str oai:repositorio.ufu.br:123456789/14831
network_acronym_str UFU
network_name_str Repositório Institucional da UFU
repository_id_str
spelling 2016-06-22T18:40:04Z2009-05-252016-06-22T18:40:04Z2008-05-09NASCIMENTO, Vinicius Castanheira do. Selection of resistance spot welding parameters, based on the measurement of the electrical resistance between sheets. 2008. 130 f. Dissertação (Mestrado em Engenharias) - Universidade Federal de Uberlândia, Uberlândia, 2008.https://repositorio.ufu.br/handle/123456789/14831Resistance Spot Welding applied in production lines may demand previous programming for welding parameter settings as a function of demanded sequential changes, due to as much as material type as thickness. In the case of a manual operation, the operator is the one in charge of changing the program when different welding conditions is identified in a same sequence of spots. Considering being an online operation, this is a potential source of error. Thus, the main motivation for this work was to verify the possibility of parameter regulation in a spot welding production line, based on measurement of the electrical resistance between the sheets. A series of experiments was carried out to verify the minimum number of cycles and the ideal electrical power needed to measure the electrical resistances between carbon steel and galvanized steel and between a different thickness sheets. The results showed that the electrical resistance can be determined from only six cycles and that it is possible to differentiate sheet combinations. They also reveal that the resistances variation amongst sheet combinations were repetitive and distinguished enough to claim the use of this principle to classify the material combinations by regions of electrical resistance, both by the difference in thickness and type of superficial coating. In this work, it was also defined the technique known as the Burn Zinc and presented an experimental procedure to achieve optimal parameters to use this technique.A aplicação da solda a ponto por resistência elétrica em produção em série pode vir a requerer uma programação prévia de variação da regulagem de parâmetros, em função da demanda por mudança seqüencial, tanto devido ao tipo de material como a de sua espessura. Caso a operação seja manual, o operador é quem terá de fazer a troca de programa sempre que identificar diferentes condições numa mesma seqüência de pontos. Por se tratar de uma operação on-line , torna-se uma fonte de erro em potencial. Dessa forma, a principal motivação deste trabalho foi a verificação da possibilidade de se regular os parâmetros de soldagem para soldas a ponto em produção, baseado na medição da resistência elétrica das combinações entre chapas. Uma série de experimentos foi realizada para verificar os parâmetros e o número mínimo de ciclos ideal para se medir a resistência elétrica entre chapas de aço com e sem revestimentos com diferentes combinações de espessura. Verificou-se que é possível se determinar a resistência elétrica de uma combinação de espessuras de chapas com apenas seis ciclos e que a variação da resistência era suficientemente repetitiva e diferenciada para justificar o uso deste princípio na separação de combinações por regiões definidas pela resistência elétrica, tanto pela diferença de espessura das combinações, como pelo tipo de revestimento da superfície. No trabalho também foi definida a técnica conhecida como Queima do Zinco ( burn-zinc ) e apresentado um procedimento experimental para se conseguir os parâmetros ótimos para a realização da técnica para combinações entre chapas galvanizadas.Coordenação de Aperfeiçoamento de Pessoal de Nível SuperiorMestre em Engenharia Mecânicaapplication/pdfporUniversidade Federal de UberlândiaPrograma de Pós-graduação em Engenharia MecânicaUFUBREngenhariasSoldagem a ponto por resistênciaResistência elétricaResistência dinâmicaAuto-regulagemQueima do zincoSoldagemResistance spot weldingRSWElectrical resistanceDynamic resistanceBurn-zincCNPQ::ENGENHARIAS::ENGENHARIA MECANICASeleção de parâmetros de soldagem a ponto por resistência, baseado na medição da resistência elétrica entre chapasSelection of resistance spot welding parameters, based on the measurement of the electrical resistance between sheetsinfo:eu-repo/semantics/publishedVersioninfo:eu-repo/semantics/masterThesisScotti, Américohttp://buscatextual.cnpq.br/buscatextual/visualizacv.do?id=K4781109E4Vilarinho, Louriel Oliveirahttp://buscatextual.cnpq.br/buscatextual/visualizacv.do?id=K4707975Z6Ferraresi, Valtair Antoniohttp://buscatextual.cnpq.br/buscatextual/visualizacv.do?id=K4787800U3Batalha, Gilmar Ferreirahttp://buscatextual.cnpq.br/buscatextual/visualizacv.do?id=K4780788T2http://buscatextual.cnpq.br/buscatextual/visualizacv.do?id=K4735559P6Nascimento, Vinicius Castanheira doinfo:eu-repo/semantics/openAccessreponame:Repositório Institucional da UFUinstname:Universidade Federal de Uberlândia (UFU)instacron:UFUTHUMBNAILVinicius.pdf.jpgVinicius.pdf.jpgGenerated Thumbnailimage/jpeg1294https://repositorio.ufu.br/bitstream/123456789/14831/3/Vinicius.pdf.jpg89f16d753e93a9714a3f19634a6dff02MD53ORIGINALVinicius.pdfapplication/pdf3837798https://repositorio.ufu.br/bitstream/123456789/14831/1/Vinicius.pdf3e03aa960cb2ff46cb1533f0328b064fMD51TEXTVinicius.pdf.txtVinicius.pdf.txtExtracted texttext/plain220860https://repositorio.ufu.br/bitstream/123456789/14831/2/Vinicius.pdf.txtc5b92fd811f6cfe5b3daf64c988ca5a2MD52123456789/148312016-06-23 04:05:54.238oai:repositorio.ufu.br:123456789/14831Repositório InstitucionalONGhttp://repositorio.ufu.br/oai/requestdiinf@dirbi.ufu.bropendoar:2024-04-26T15:04:48.621500Repositório Institucional da UFU - Universidade Federal de Uberlândia (UFU)false
dc.title.por.fl_str_mv Seleção de parâmetros de soldagem a ponto por resistência, baseado na medição da resistência elétrica entre chapas
dc.title.alternative.eng.fl_str_mv Selection of resistance spot welding parameters, based on the measurement of the electrical resistance between sheets
title Seleção de parâmetros de soldagem a ponto por resistência, baseado na medição da resistência elétrica entre chapas
spellingShingle Seleção de parâmetros de soldagem a ponto por resistência, baseado na medição da resistência elétrica entre chapas
Nascimento, Vinicius Castanheira do
Soldagem a ponto por resistência
Resistência elétrica
Resistência dinâmica
Auto-regulagem
Queima do zinco
Soldagem
Resistance spot welding
RSW
Electrical resistance
Dynamic resistance
Burn-zinc
CNPQ::ENGENHARIAS::ENGENHARIA MECANICA
title_short Seleção de parâmetros de soldagem a ponto por resistência, baseado na medição da resistência elétrica entre chapas
title_full Seleção de parâmetros de soldagem a ponto por resistência, baseado na medição da resistência elétrica entre chapas
title_fullStr Seleção de parâmetros de soldagem a ponto por resistência, baseado na medição da resistência elétrica entre chapas
title_full_unstemmed Seleção de parâmetros de soldagem a ponto por resistência, baseado na medição da resistência elétrica entre chapas
title_sort Seleção de parâmetros de soldagem a ponto por resistência, baseado na medição da resistência elétrica entre chapas
author Nascimento, Vinicius Castanheira do
author_facet Nascimento, Vinicius Castanheira do
author_role author
dc.contributor.advisor1.fl_str_mv Scotti, Américo
dc.contributor.advisor1Lattes.fl_str_mv http://buscatextual.cnpq.br/buscatextual/visualizacv.do?id=K4781109E4
dc.contributor.referee1.fl_str_mv Vilarinho, Louriel Oliveira
dc.contributor.referee1Lattes.fl_str_mv http://buscatextual.cnpq.br/buscatextual/visualizacv.do?id=K4707975Z6
dc.contributor.referee2.fl_str_mv Ferraresi, Valtair Antonio
dc.contributor.referee2Lattes.fl_str_mv http://buscatextual.cnpq.br/buscatextual/visualizacv.do?id=K4787800U3
dc.contributor.referee3.fl_str_mv Batalha, Gilmar Ferreira
dc.contributor.referee3Lattes.fl_str_mv http://buscatextual.cnpq.br/buscatextual/visualizacv.do?id=K4780788T2
dc.contributor.authorLattes.fl_str_mv http://buscatextual.cnpq.br/buscatextual/visualizacv.do?id=K4735559P6
dc.contributor.author.fl_str_mv Nascimento, Vinicius Castanheira do
contributor_str_mv Scotti, Américo
Vilarinho, Louriel Oliveira
Ferraresi, Valtair Antonio
Batalha, Gilmar Ferreira
dc.subject.por.fl_str_mv Soldagem a ponto por resistência
Resistência elétrica
Resistência dinâmica
Auto-regulagem
Queima do zinco
Soldagem
topic Soldagem a ponto por resistência
Resistência elétrica
Resistência dinâmica
Auto-regulagem
Queima do zinco
Soldagem
Resistance spot welding
RSW
Electrical resistance
Dynamic resistance
Burn-zinc
CNPQ::ENGENHARIAS::ENGENHARIA MECANICA
dc.subject.eng.fl_str_mv Resistance spot welding
RSW
Electrical resistance
Dynamic resistance
Burn-zinc
dc.subject.cnpq.fl_str_mv CNPQ::ENGENHARIAS::ENGENHARIA MECANICA
description Resistance Spot Welding applied in production lines may demand previous programming for welding parameter settings as a function of demanded sequential changes, due to as much as material type as thickness. In the case of a manual operation, the operator is the one in charge of changing the program when different welding conditions is identified in a same sequence of spots. Considering being an online operation, this is a potential source of error. Thus, the main motivation for this work was to verify the possibility of parameter regulation in a spot welding production line, based on measurement of the electrical resistance between the sheets. A series of experiments was carried out to verify the minimum number of cycles and the ideal electrical power needed to measure the electrical resistances between carbon steel and galvanized steel and between a different thickness sheets. The results showed that the electrical resistance can be determined from only six cycles and that it is possible to differentiate sheet combinations. They also reveal that the resistances variation amongst sheet combinations were repetitive and distinguished enough to claim the use of this principle to classify the material combinations by regions of electrical resistance, both by the difference in thickness and type of superficial coating. In this work, it was also defined the technique known as the Burn Zinc and presented an experimental procedure to achieve optimal parameters to use this technique.
publishDate 2008
dc.date.issued.fl_str_mv 2008-05-09
dc.date.available.fl_str_mv 2009-05-25
2016-06-22T18:40:04Z
dc.date.accessioned.fl_str_mv 2016-06-22T18:40:04Z
dc.type.status.fl_str_mv info:eu-repo/semantics/publishedVersion
dc.type.driver.fl_str_mv info:eu-repo/semantics/masterThesis
format masterThesis
status_str publishedVersion
dc.identifier.citation.fl_str_mv NASCIMENTO, Vinicius Castanheira do. Selection of resistance spot welding parameters, based on the measurement of the electrical resistance between sheets. 2008. 130 f. Dissertação (Mestrado em Engenharias) - Universidade Federal de Uberlândia, Uberlândia, 2008.
dc.identifier.uri.fl_str_mv https://repositorio.ufu.br/handle/123456789/14831
identifier_str_mv NASCIMENTO, Vinicius Castanheira do. Selection of resistance spot welding parameters, based on the measurement of the electrical resistance between sheets. 2008. 130 f. Dissertação (Mestrado em Engenharias) - Universidade Federal de Uberlândia, Uberlândia, 2008.
url https://repositorio.ufu.br/handle/123456789/14831
dc.language.iso.fl_str_mv por
language por
dc.rights.driver.fl_str_mv info:eu-repo/semantics/openAccess
eu_rights_str_mv openAccess
dc.format.none.fl_str_mv application/pdf
dc.publisher.none.fl_str_mv Universidade Federal de Uberlândia
dc.publisher.program.fl_str_mv Programa de Pós-graduação em Engenharia Mecânica
dc.publisher.initials.fl_str_mv UFU
dc.publisher.country.fl_str_mv BR
dc.publisher.department.fl_str_mv Engenharias
publisher.none.fl_str_mv Universidade Federal de Uberlândia
dc.source.none.fl_str_mv reponame:Repositório Institucional da UFU
instname:Universidade Federal de Uberlândia (UFU)
instacron:UFU
instname_str Universidade Federal de Uberlândia (UFU)
instacron_str UFU
institution UFU
reponame_str Repositório Institucional da UFU
collection Repositório Institucional da UFU
bitstream.url.fl_str_mv https://repositorio.ufu.br/bitstream/123456789/14831/3/Vinicius.pdf.jpg
https://repositorio.ufu.br/bitstream/123456789/14831/1/Vinicius.pdf
https://repositorio.ufu.br/bitstream/123456789/14831/2/Vinicius.pdf.txt
bitstream.checksum.fl_str_mv 89f16d753e93a9714a3f19634a6dff02
3e03aa960cb2ff46cb1533f0328b064f
c5b92fd811f6cfe5b3daf64c988ca5a2
bitstream.checksumAlgorithm.fl_str_mv MD5
MD5
MD5
repository.name.fl_str_mv Repositório Institucional da UFU - Universidade Federal de Uberlândia (UFU)
repository.mail.fl_str_mv diinf@dirbi.ufu.br
_version_ 1797425552393502720