Preparação, caracterização físico-química e avaliação do comportamento térmico e mecânico de blendas de poli (tereftalato de etileno) (PET) e poli (éterimidia) (PEI), PET/PEI
Autor(a) principal: | |
---|---|
Data de Publicação: | 2004 |
Tipo de documento: | Tese |
Idioma: | por |
Título da fonte: | Repositório Institucional da UFSCAR |
Texto Completo: | https://repositorio.ufscar.br/handle/ufscar/6102 |
Resumo: | The blends preparation and composites have been one of the techniques more used to make possible properties and to increase the time of useful life of polymers. PET is a polymeric semicrystalline that has a Tg in 75°C and Tm in 245°C. The low value of Tg of PET and its easiness in crystallizing a lot of times points negative not desired can be considered in a certain project. PEI is a polymeric one amorphous with a value of Tg quite loud 215°C. In the mixture of PET (virgin or recycled) with PEI a displacement was verified in Tg of PET, as well as the one of PEI suggesting polymeric miscibility of the two in the melted state and confirmed later on by the negative value of the parameter of certain Flory to thermal treatments. Since the fusion entalpia is proportional to the crystalline fraction, its correlation with the conformer Reason Trans, RT, was found linear and independent of the content of PEI, turning possible to the determination of the degree of cristalinidade of independent PET of which it goes the composition of to blend PET/PEI. From the results of mechanical resistance of the samples submitted to the aging under radiation UV, it was verified that, independent of the type of PET employee, of the time of radiation of the condition dry or after immersion in water, for stabilized blends or not, so much the specific deformation in the rupture, elastic module, the deformation, and calculated elastic energy, they show a continuous tendency of growth with increase of the content of PEI in the mixture. The effective protection of PEI was verified on PET starting from 25% in PEI of up to 200h of exhibition under UV for the dry samples and up to 100h for samples after immersion in water. After thermal cycle it was verified that, depending on the temperature of the test the composition becomes an important factor. The thermal treatment above 90°C in the presence of the blends with larger concentration than 25% in PEI eliminate the tensions frozen during the processing, in other words, physical aging without there is the crystallization of PET, consequently, a significant improvement was observed in the mechanical answer in terms of elastic energy until tenth cycle. The thermal cycle at 120°C and 140°C is committed for the physical aging of PET and crystallization after the first cycle. The results obtained for the blend with content of 25% in PEI, in fact, when compared to the samples of pure PET they evidence the significant gain in the value of the elastic energy, these results suggest the potentiality for a possible application of this blend in the production of pieces whose interest is to guarantee a good resistance to the impact. |
id |
SCAR_0a5517f587d8729ff595675bc63889a3 |
---|---|
oai_identifier_str |
oai:repositorio.ufscar.br:ufscar/6102 |
network_acronym_str |
SCAR |
network_name_str |
Repositório Institucional da UFSCAR |
repository_id_str |
4322 |
spelling |
Barros, Adriana de FátimaRuvolo Filho, Adhemar Collahttp://genos.cnpq.br:12010/dwlattes/owa/prc_imp_cv_int?f_cod=K4787583A009526737-b8b7-441f-a2eb-72e399efca742016-06-02T20:34:09Z2008-08-222016-06-02T20:34:09Z2004-11-19BARROS, Adriana de Fátima. Preparation, physical-chemical characterization and evaluation of the thermal and mechanical behavior of blends of poly (terephtalate of ethylene)(PET) and poly(etherimide)(PEI), PET/PEI. 2004. 254 f. Tese (Doutorado em Ciências Exatas e da Terra) - Universidade Federal de São Carlos, São Carlos, 2004.https://repositorio.ufscar.br/handle/ufscar/6102The blends preparation and composites have been one of the techniques more used to make possible properties and to increase the time of useful life of polymers. PET is a polymeric semicrystalline that has a Tg in 75°C and Tm in 245°C. The low value of Tg of PET and its easiness in crystallizing a lot of times points negative not desired can be considered in a certain project. PEI is a polymeric one amorphous with a value of Tg quite loud 215°C. In the mixture of PET (virgin or recycled) with PEI a displacement was verified in Tg of PET, as well as the one of PEI suggesting polymeric miscibility of the two in the melted state and confirmed later on by the negative value of the parameter of certain Flory to thermal treatments. Since the fusion entalpia is proportional to the crystalline fraction, its correlation with the conformer Reason Trans, RT, was found linear and independent of the content of PEI, turning possible to the determination of the degree of cristalinidade of independent PET of which it goes the composition of to blend PET/PEI. From the results of mechanical resistance of the samples submitted to the aging under radiation UV, it was verified that, independent of the type of PET employee, of the time of radiation of the condition dry or after immersion in water, for stabilized blends or not, so much the specific deformation in the rupture, elastic module, the deformation, and calculated elastic energy, they show a continuous tendency of growth with increase of the content of PEI in the mixture. The effective protection of PEI was verified on PET starting from 25% in PEI of up to 200h of exhibition under UV for the dry samples and up to 100h for samples after immersion in water. After thermal cycle it was verified that, depending on the temperature of the test the composition becomes an important factor. The thermal treatment above 90°C in the presence of the blends with larger concentration than 25% in PEI eliminate the tensions frozen during the processing, in other words, physical aging without there is the crystallization of PET, consequently, a significant improvement was observed in the mechanical answer in terms of elastic energy until tenth cycle. The thermal cycle at 120°C and 140°C is committed for the physical aging of PET and crystallization after the first cycle. The results obtained for the blend with content of 25% in PEI, in fact, when compared to the samples of pure PET they evidence the significant gain in the value of the elastic energy, these results suggest the potentiality for a possible application of this blend in the production of pieces whose interest is to guarantee a good resistance to the impact.A preparação de blendas e compósitos tem sido umas das técnicas mais utilizadas para viabilizar propriedades e aumentar o tempo de vida útil de polímeros. O PET é um polímero semicristalino que possui Tg em 75°C e Tm em 245°C. O baixo valor da Tg do PET e sua facilidade em cristalizar muitas vezes podem ser considerados pontos negativos indesejados em um determinado projeto. A PEI é um polímero amorfo com um valor de Tg bastante alto 215°C. Na mistura de PET (virgem ou reciclado) com PEI foi verificado um deslocamento na Tg do PET, bem como a do PEI sugerindo miscibilidade do dois polímeros no estado fundido e confirmado pelo valor negativo do parâmetro de Flory determinado posteriormente a tratamentos térmicos. Desde que a entalpia de fusão é proporcional à fração cristalina, sua correlação com a Razão de conformação Trans, RT, foi encontrada linear e independente do conteúdo de PEI, tornando possível à determinação do grau de cristalinidade do PET independente de qual for a composição da blenda PET/PEI. A partir dos resultados de resistência mecânica das amostras submetidas ao envelhecimento sob radiação UV, verificou-se que, independente do tipo de PET empregado, do tempo de radiação da condição seco ou após imersão em água, para blendas estabilizadas ou não, tanto a deformação específica na ruptura, módulo elástico, a elongação, e energia elástica calculada, mostram uma tendência contínua de crescimento com aumento do conteúdo de PEI na mistura. Foi verificada a proteção efetiva da PEI sobre o PET a partir de 25% em PEI de até 200h de exposição sob UV para as amostras secas e até 100h para amostras após imersão em água.Após ciclagem térmica verificou-se que, dependendo da temperatura de ensaio de ciclo térmico a composição passa a ser um fator importante. O tratamento térmico acima de 90°C na presença das blendas com concentração maior que 25% em PEI elimina as tensões congeladas durante o processamento, ou seja, envelhecimento físico sem que haja a cristalização do PET, conseqüentemente observou-se uma melhoria significativa na resposta mecânica em termos de energia elástica até o décimo ciclo. A ciclagem térmica a 120°C e a 140°C são comprometidas pelo envelhecimento físico do PET e cristalização após o primeiro ciclo.Os resultados obtidos para a blenda com conteúdo de 25% em PEI, de fato, quando comparados às amostras de PET puro evidenciam o ganho significativo no valor da energia elástica, estes resultados sugerem a potencialidade para uma possível aplicação desta blenda na produção de peças cujo interesse é garantir uma boa resistência ao impacto.Universidade Federal de Sao Carlosapplication/pdfporUniversidade Federal de São CarlosPrograma de Pós-Graduação em Química - PPGQUFSCarBRPolímerosBlendas poliméricasPET(Polietileno tereftalato)PEI (Polieterimidia)Reciclagem de materiais poliméricosCIENCIAS EXATAS E DA TERRA::QUIMICAPreparação, caracterização físico-química e avaliação do comportamento térmico e mecânico de blendas de poli (tereftalato de etileno) (PET) e poli (éterimidia) (PEI), PET/PEIPreparation, physical-chemical characterization and evaluation of the thermal and mechanical behavior of blends of poly (terephtalate of ethylene)(PET) and poly(etherimide)(PEI), PET/PEIinfo:eu-repo/semantics/publishedVersioninfo:eu-repo/semantics/doctoralThesis-1-10b030418-f310-498e-a166-e7c18306af8einfo:eu-repo/semantics/openAccessreponame:Repositório Institucional da UFSCARinstname:Universidade Federal de São Carlos (UFSCAR)instacron:UFSCARORIGINAL1942.pdfapplication/pdf3920831https://repositorio.ufscar.br/bitstream/ufscar/6102/1/1942.pdfc7ebcbad9fc4c1e3b98154fe862136b2MD51THUMBNAIL1942.pdf.jpg1942.pdf.jpgIM Thumbnailimage/jpeg10640https://repositorio.ufscar.br/bitstream/ufscar/6102/2/1942.pdf.jpg6ade403b1a4988529956012bd615c450MD52ufscar/61022023-09-18 18:31:10.861oai:repositorio.ufscar.br:ufscar/6102Repositório InstitucionalPUBhttps://repositorio.ufscar.br/oai/requestopendoar:43222023-09-18T18:31:10Repositório Institucional da UFSCAR - Universidade Federal de São Carlos (UFSCAR)false |
dc.title.por.fl_str_mv |
Preparação, caracterização físico-química e avaliação do comportamento térmico e mecânico de blendas de poli (tereftalato de etileno) (PET) e poli (éterimidia) (PEI), PET/PEI |
dc.title.alternative.eng.fl_str_mv |
Preparation, physical-chemical characterization and evaluation of the thermal and mechanical behavior of blends of poly (terephtalate of ethylene)(PET) and poly(etherimide)(PEI), PET/PEI |
title |
Preparação, caracterização físico-química e avaliação do comportamento térmico e mecânico de blendas de poli (tereftalato de etileno) (PET) e poli (éterimidia) (PEI), PET/PEI |
spellingShingle |
Preparação, caracterização físico-química e avaliação do comportamento térmico e mecânico de blendas de poli (tereftalato de etileno) (PET) e poli (éterimidia) (PEI), PET/PEI Barros, Adriana de Fátima Polímeros Blendas poliméricas PET(Polietileno tereftalato) PEI (Polieterimidia) Reciclagem de materiais poliméricos CIENCIAS EXATAS E DA TERRA::QUIMICA |
title_short |
Preparação, caracterização físico-química e avaliação do comportamento térmico e mecânico de blendas de poli (tereftalato de etileno) (PET) e poli (éterimidia) (PEI), PET/PEI |
title_full |
Preparação, caracterização físico-química e avaliação do comportamento térmico e mecânico de blendas de poli (tereftalato de etileno) (PET) e poli (éterimidia) (PEI), PET/PEI |
title_fullStr |
Preparação, caracterização físico-química e avaliação do comportamento térmico e mecânico de blendas de poli (tereftalato de etileno) (PET) e poli (éterimidia) (PEI), PET/PEI |
title_full_unstemmed |
Preparação, caracterização físico-química e avaliação do comportamento térmico e mecânico de blendas de poli (tereftalato de etileno) (PET) e poli (éterimidia) (PEI), PET/PEI |
title_sort |
Preparação, caracterização físico-química e avaliação do comportamento térmico e mecânico de blendas de poli (tereftalato de etileno) (PET) e poli (éterimidia) (PEI), PET/PEI |
author |
Barros, Adriana de Fátima |
author_facet |
Barros, Adriana de Fátima |
author_role |
author |
dc.contributor.author.fl_str_mv |
Barros, Adriana de Fátima |
dc.contributor.advisor1.fl_str_mv |
Ruvolo Filho, Adhemar Colla |
dc.contributor.advisor1Lattes.fl_str_mv |
http://genos.cnpq.br:12010/dwlattes/owa/prc_imp_cv_int?f_cod=K4787583A0 |
dc.contributor.authorID.fl_str_mv |
09526737-b8b7-441f-a2eb-72e399efca74 |
contributor_str_mv |
Ruvolo Filho, Adhemar Colla |
dc.subject.por.fl_str_mv |
Polímeros Blendas poliméricas PET(Polietileno tereftalato) PEI (Polieterimidia) Reciclagem de materiais poliméricos |
topic |
Polímeros Blendas poliméricas PET(Polietileno tereftalato) PEI (Polieterimidia) Reciclagem de materiais poliméricos CIENCIAS EXATAS E DA TERRA::QUIMICA |
dc.subject.cnpq.fl_str_mv |
CIENCIAS EXATAS E DA TERRA::QUIMICA |
description |
The blends preparation and composites have been one of the techniques more used to make possible properties and to increase the time of useful life of polymers. PET is a polymeric semicrystalline that has a Tg in 75°C and Tm in 245°C. The low value of Tg of PET and its easiness in crystallizing a lot of times points negative not desired can be considered in a certain project. PEI is a polymeric one amorphous with a value of Tg quite loud 215°C. In the mixture of PET (virgin or recycled) with PEI a displacement was verified in Tg of PET, as well as the one of PEI suggesting polymeric miscibility of the two in the melted state and confirmed later on by the negative value of the parameter of certain Flory to thermal treatments. Since the fusion entalpia is proportional to the crystalline fraction, its correlation with the conformer Reason Trans, RT, was found linear and independent of the content of PEI, turning possible to the determination of the degree of cristalinidade of independent PET of which it goes the composition of to blend PET/PEI. From the results of mechanical resistance of the samples submitted to the aging under radiation UV, it was verified that, independent of the type of PET employee, of the time of radiation of the condition dry or after immersion in water, for stabilized blends or not, so much the specific deformation in the rupture, elastic module, the deformation, and calculated elastic energy, they show a continuous tendency of growth with increase of the content of PEI in the mixture. The effective protection of PEI was verified on PET starting from 25% in PEI of up to 200h of exhibition under UV for the dry samples and up to 100h for samples after immersion in water. After thermal cycle it was verified that, depending on the temperature of the test the composition becomes an important factor. The thermal treatment above 90°C in the presence of the blends with larger concentration than 25% in PEI eliminate the tensions frozen during the processing, in other words, physical aging without there is the crystallization of PET, consequently, a significant improvement was observed in the mechanical answer in terms of elastic energy until tenth cycle. The thermal cycle at 120°C and 140°C is committed for the physical aging of PET and crystallization after the first cycle. The results obtained for the blend with content of 25% in PEI, in fact, when compared to the samples of pure PET they evidence the significant gain in the value of the elastic energy, these results suggest the potentiality for a possible application of this blend in the production of pieces whose interest is to guarantee a good resistance to the impact. |
publishDate |
2004 |
dc.date.issued.fl_str_mv |
2004-11-19 |
dc.date.available.fl_str_mv |
2008-08-22 2016-06-02T20:34:09Z |
dc.date.accessioned.fl_str_mv |
2016-06-02T20:34:09Z |
dc.type.status.fl_str_mv |
info:eu-repo/semantics/publishedVersion |
dc.type.driver.fl_str_mv |
info:eu-repo/semantics/doctoralThesis |
format |
doctoralThesis |
status_str |
publishedVersion |
dc.identifier.citation.fl_str_mv |
BARROS, Adriana de Fátima. Preparation, physical-chemical characterization and evaluation of the thermal and mechanical behavior of blends of poly (terephtalate of ethylene)(PET) and poly(etherimide)(PEI), PET/PEI. 2004. 254 f. Tese (Doutorado em Ciências Exatas e da Terra) - Universidade Federal de São Carlos, São Carlos, 2004. |
dc.identifier.uri.fl_str_mv |
https://repositorio.ufscar.br/handle/ufscar/6102 |
identifier_str_mv |
BARROS, Adriana de Fátima. Preparation, physical-chemical characterization and evaluation of the thermal and mechanical behavior of blends of poly (terephtalate of ethylene)(PET) and poly(etherimide)(PEI), PET/PEI. 2004. 254 f. Tese (Doutorado em Ciências Exatas e da Terra) - Universidade Federal de São Carlos, São Carlos, 2004. |
url |
https://repositorio.ufscar.br/handle/ufscar/6102 |
dc.language.iso.fl_str_mv |
por |
language |
por |
dc.relation.confidence.fl_str_mv |
-1 -1 |
dc.relation.authority.fl_str_mv |
0b030418-f310-498e-a166-e7c18306af8e |
dc.rights.driver.fl_str_mv |
info:eu-repo/semantics/openAccess |
eu_rights_str_mv |
openAccess |
dc.format.none.fl_str_mv |
application/pdf |
dc.publisher.none.fl_str_mv |
Universidade Federal de São Carlos |
dc.publisher.program.fl_str_mv |
Programa de Pós-Graduação em Química - PPGQ |
dc.publisher.initials.fl_str_mv |
UFSCar |
dc.publisher.country.fl_str_mv |
BR |
publisher.none.fl_str_mv |
Universidade Federal de São Carlos |
dc.source.none.fl_str_mv |
reponame:Repositório Institucional da UFSCAR instname:Universidade Federal de São Carlos (UFSCAR) instacron:UFSCAR |
instname_str |
Universidade Federal de São Carlos (UFSCAR) |
instacron_str |
UFSCAR |
institution |
UFSCAR |
reponame_str |
Repositório Institucional da UFSCAR |
collection |
Repositório Institucional da UFSCAR |
bitstream.url.fl_str_mv |
https://repositorio.ufscar.br/bitstream/ufscar/6102/1/1942.pdf https://repositorio.ufscar.br/bitstream/ufscar/6102/2/1942.pdf.jpg |
bitstream.checksum.fl_str_mv |
c7ebcbad9fc4c1e3b98154fe862136b2 6ade403b1a4988529956012bd615c450 |
bitstream.checksumAlgorithm.fl_str_mv |
MD5 MD5 |
repository.name.fl_str_mv |
Repositório Institucional da UFSCAR - Universidade Federal de São Carlos (UFSCAR) |
repository.mail.fl_str_mv |
|
_version_ |
1802136291325771776 |