Estudo da flexo-compressão normal em pilares de concreto armado utilizando o método iterativo para o cálculo da armadura longitudinal
Autor(a) principal: | |
---|---|
Data de Publicação: | 2019 |
Tipo de documento: | Trabalho de conclusão de curso |
Idioma: | por |
Título da fonte: | Repositório Institucional da Universidade Federal de Alagoas (UFAL) |
Texto Completo: | http://www.repositorio.ufal.br/handle/riufal/6343 |
Resumo: | At the academic level, the sizing of columns is usually performed using abacus. However, abacus considers some numerical parameters that do not apply to high performance concretes (group II). Alternatively, the iterative method can be used. In this sense, the present work conducts a study on the uniaxial flexural compression, in two rectangular reinforced concrete columns, with slenderness less than 90, with concrete of groups I and II of resistance defined by ABNT NBR 6118: 2014, using of the iterative method to obtain the steel ratio. For the first example the differences in the steel area are compared between the iterative method sizing and the sizing by the traditional method, for group I concrete, in which the mechanical steel ratio is obtained by means of abacuses. The relationship of the concrete resistance and the amount of steel needed to withstand the requests is also evaluated. In the second example a comparison is made between the standard-column method with approximate curvature and the standard-column method with approximate stiffness. The iterative method sizing resulted in areas somewhat less than using abacuses and the steel area was significantly reduced with increasing concrete resistance, the greatest reductions were observed in situations with greater axial force. The standard-column method with approximate stiffness, in general, resulted in smaller steel consumption, with the difference decreasing as the axial force is increased, presenting a steel consumption larger than the standard-column method with approximate curvature to very high values of axial force. |
id |
UFAL_7ce726b81685e3ac062e78c9e1d4f6a3 |
---|---|
oai_identifier_str |
oai:www.repositorio.ufal.br:riufal/6343 |
network_acronym_str |
UFAL |
network_name_str |
Repositório Institucional da Universidade Federal de Alagoas (UFAL) |
repository_id_str |
|
spelling |
Estudo da flexo-compressão normal em pilares de concreto armado utilizando o método iterativo para o cálculo da armadura longitudinalDimensionamentoConcreto armadoFlexo-compressor normalMétodo iterativoCNPQ::ENGENHARIAS::ENGENHARIA CIVIL::ESTRUTURAS::ESTRUTURAS DE CONCRETOAt the academic level, the sizing of columns is usually performed using abacus. However, abacus considers some numerical parameters that do not apply to high performance concretes (group II). Alternatively, the iterative method can be used. In this sense, the present work conducts a study on the uniaxial flexural compression, in two rectangular reinforced concrete columns, with slenderness less than 90, with concrete of groups I and II of resistance defined by ABNT NBR 6118: 2014, using of the iterative method to obtain the steel ratio. For the first example the differences in the steel area are compared between the iterative method sizing and the sizing by the traditional method, for group I concrete, in which the mechanical steel ratio is obtained by means of abacuses. The relationship of the concrete resistance and the amount of steel needed to withstand the requests is also evaluated. In the second example a comparison is made between the standard-column method with approximate curvature and the standard-column method with approximate stiffness. The iterative method sizing resulted in areas somewhat less than using abacuses and the steel area was significantly reduced with increasing concrete resistance, the greatest reductions were observed in situations with greater axial force. The standard-column method with approximate stiffness, in general, resulted in smaller steel consumption, with the difference decreasing as the axial force is increased, presenting a steel consumption larger than the standard-column method with approximate curvature to very high values of axial force.A nível acadêmico, o dimensionamento de pilares é costumeiramente realizado com a utilização de ábacos. Contudo, os ábacos consideram alguns parâmetros numéricos que não se aplicam a concretos de alto desempenho (grupo II). Assim, como alternativa pode-se utilizar o método iterativo. Neste sentido, o presente trabalho realiza um estudo sobre a flexo-compressão normal, em dois pilares retangulares de concreto armado, com esbeltez inferior a 90, com concretos dos grupos I e II de resistência definidos pela ABNT NBR 6118:2014, utilizando-se do método iterativo para a obtenção da área de aço. Para o primeiro exemplo são comparadas as diferenças na área de aço entre o dimensionamento pelo método iterativo e o dimensionamento pelo método tradicional, para concretos do grupo I, no qual a taxa mecânica é obtida por meio de ábacos. Avalia-se ainda a relação entre a resistência do concreto e a quantidade de aço necessária para suportar os esforços solicitantes. No segundo exemplo é feita uma comparação entre o método aproximado do pilarpadrão com curvatura aproximada e do pilar padrão com rigidez aproximada. O dimensionamento pelo método iterativo resultou em armaduras levemente inferiores ao dimensionamento com ábacos e a área de aço foi reduzida significativamente com o aumento da resistência do concreto, onde as maiores reduções foram observadas nas situações com maiores esforços normais solicitantes. E o método do pilar-padrão com rigidez aproximada, no geral, resultou em armaduras menores, com a diferença diminuindo a medida em que se aumentava o esforço normal, chegando a apresentar armaduras maiores que o método do pilar-padrão com curvatura aproximada para valores muito elevados do esforço normal.Universidade Federal de AlagoasBrasilCurso de Engenharia CivilUFALRicardo, Alverlando Silvahttp://lattes.cnpq.br/2899168876084507Correia, Vinícius CostaFalcão, Victor BezerraAlves, Ericson Simião2020-01-08T16:18:08Z2020-01-082020-01-08T16:18:08Z2019-12-19info:eu-repo/semantics/publishedVersioninfo:eu-repo/semantics/bachelorThesisapplication/pdfALVES, Ericson Simião. Estudo da flexo-compressão normal em pilares de concreto armado utilizando o método iterativo para o cálculo da armadura longitudinal. 2019. 72 f. Trabalho de Conclusão de Curso (Bacharelado em Engenharia Civil) - Unidade Delmiro Gouveia-Campus do Sertão, Universidade Federal de Alagoas, Delmiro Gouveia, 2019.http://www.repositorio.ufal.br/handle/riufal/6343porinfo:eu-repo/semantics/openAccessreponame:Repositório Institucional da Universidade Federal de Alagoas (UFAL)instname:Universidade Federal de Alagoas (UFAL)instacron:UFAL2021-09-08T15:11:19Zoai:www.repositorio.ufal.br:riufal/6343Repositório InstitucionalPUBhttp://www.repositorio.ufal.br/oai/requestri@sibi.ufal.bropendoar:2021-09-08T15:11:19Repositório Institucional da Universidade Federal de Alagoas (UFAL) - Universidade Federal de Alagoas (UFAL)false |
dc.title.none.fl_str_mv |
Estudo da flexo-compressão normal em pilares de concreto armado utilizando o método iterativo para o cálculo da armadura longitudinal |
title |
Estudo da flexo-compressão normal em pilares de concreto armado utilizando o método iterativo para o cálculo da armadura longitudinal |
spellingShingle |
Estudo da flexo-compressão normal em pilares de concreto armado utilizando o método iterativo para o cálculo da armadura longitudinal Alves, Ericson Simião Dimensionamento Concreto armado Flexo-compressor normal Método iterativo CNPQ::ENGENHARIAS::ENGENHARIA CIVIL::ESTRUTURAS::ESTRUTURAS DE CONCRETO |
title_short |
Estudo da flexo-compressão normal em pilares de concreto armado utilizando o método iterativo para o cálculo da armadura longitudinal |
title_full |
Estudo da flexo-compressão normal em pilares de concreto armado utilizando o método iterativo para o cálculo da armadura longitudinal |
title_fullStr |
Estudo da flexo-compressão normal em pilares de concreto armado utilizando o método iterativo para o cálculo da armadura longitudinal |
title_full_unstemmed |
Estudo da flexo-compressão normal em pilares de concreto armado utilizando o método iterativo para o cálculo da armadura longitudinal |
title_sort |
Estudo da flexo-compressão normal em pilares de concreto armado utilizando o método iterativo para o cálculo da armadura longitudinal |
author |
Alves, Ericson Simião |
author_facet |
Alves, Ericson Simião |
author_role |
author |
dc.contributor.none.fl_str_mv |
Ricardo, Alverlando Silva http://lattes.cnpq.br/2899168876084507 Correia, Vinícius Costa Falcão, Victor Bezerra |
dc.contributor.author.fl_str_mv |
Alves, Ericson Simião |
dc.subject.por.fl_str_mv |
Dimensionamento Concreto armado Flexo-compressor normal Método iterativo CNPQ::ENGENHARIAS::ENGENHARIA CIVIL::ESTRUTURAS::ESTRUTURAS DE CONCRETO |
topic |
Dimensionamento Concreto armado Flexo-compressor normal Método iterativo CNPQ::ENGENHARIAS::ENGENHARIA CIVIL::ESTRUTURAS::ESTRUTURAS DE CONCRETO |
description |
At the academic level, the sizing of columns is usually performed using abacus. However, abacus considers some numerical parameters that do not apply to high performance concretes (group II). Alternatively, the iterative method can be used. In this sense, the present work conducts a study on the uniaxial flexural compression, in two rectangular reinforced concrete columns, with slenderness less than 90, with concrete of groups I and II of resistance defined by ABNT NBR 6118: 2014, using of the iterative method to obtain the steel ratio. For the first example the differences in the steel area are compared between the iterative method sizing and the sizing by the traditional method, for group I concrete, in which the mechanical steel ratio is obtained by means of abacuses. The relationship of the concrete resistance and the amount of steel needed to withstand the requests is also evaluated. In the second example a comparison is made between the standard-column method with approximate curvature and the standard-column method with approximate stiffness. The iterative method sizing resulted in areas somewhat less than using abacuses and the steel area was significantly reduced with increasing concrete resistance, the greatest reductions were observed in situations with greater axial force. The standard-column method with approximate stiffness, in general, resulted in smaller steel consumption, with the difference decreasing as the axial force is increased, presenting a steel consumption larger than the standard-column method with approximate curvature to very high values of axial force. |
publishDate |
2019 |
dc.date.none.fl_str_mv |
2019-12-19 2020-01-08T16:18:08Z 2020-01-08 2020-01-08T16:18:08Z |
dc.type.status.fl_str_mv |
info:eu-repo/semantics/publishedVersion |
dc.type.driver.fl_str_mv |
info:eu-repo/semantics/bachelorThesis |
format |
bachelorThesis |
status_str |
publishedVersion |
dc.identifier.uri.fl_str_mv |
ALVES, Ericson Simião. Estudo da flexo-compressão normal em pilares de concreto armado utilizando o método iterativo para o cálculo da armadura longitudinal. 2019. 72 f. Trabalho de Conclusão de Curso (Bacharelado em Engenharia Civil) - Unidade Delmiro Gouveia-Campus do Sertão, Universidade Federal de Alagoas, Delmiro Gouveia, 2019. http://www.repositorio.ufal.br/handle/riufal/6343 |
identifier_str_mv |
ALVES, Ericson Simião. Estudo da flexo-compressão normal em pilares de concreto armado utilizando o método iterativo para o cálculo da armadura longitudinal. 2019. 72 f. Trabalho de Conclusão de Curso (Bacharelado em Engenharia Civil) - Unidade Delmiro Gouveia-Campus do Sertão, Universidade Federal de Alagoas, Delmiro Gouveia, 2019. |
url |
http://www.repositorio.ufal.br/handle/riufal/6343 |
dc.language.iso.fl_str_mv |
por |
language |
por |
dc.rights.driver.fl_str_mv |
info:eu-repo/semantics/openAccess |
eu_rights_str_mv |
openAccess |
dc.format.none.fl_str_mv |
application/pdf |
dc.publisher.none.fl_str_mv |
Universidade Federal de Alagoas Brasil Curso de Engenharia Civil UFAL |
publisher.none.fl_str_mv |
Universidade Federal de Alagoas Brasil Curso de Engenharia Civil UFAL |
dc.source.none.fl_str_mv |
reponame:Repositório Institucional da Universidade Federal de Alagoas (UFAL) instname:Universidade Federal de Alagoas (UFAL) instacron:UFAL |
instname_str |
Universidade Federal de Alagoas (UFAL) |
instacron_str |
UFAL |
institution |
UFAL |
reponame_str |
Repositório Institucional da Universidade Federal de Alagoas (UFAL) |
collection |
Repositório Institucional da Universidade Federal de Alagoas (UFAL) |
repository.name.fl_str_mv |
Repositório Institucional da Universidade Federal de Alagoas (UFAL) - Universidade Federal de Alagoas (UFAL) |
repository.mail.fl_str_mv |
ri@sibi.ufal.br |
_version_ |
1748233746010603520 |