Performance of ISO P and ISO S carbide tools in hard turning of AISI 4140 under dry and MQL conditions

Detalhes bibliográficos
Autor(a) principal: Polly, Matheus dos Santos
Data de Publicação: 2020
Outros Autores: Mayrhofer, Amália, Souza, André João de
Tipo de documento: Artigo
Idioma: eng
Título da fonte: Repositório Institucional da UFRGS
Texto Completo: http://hdl.handle.net/10183/212751
Resumo: The literature review shows few studies concerning the turning of hardened steels using carbide tools. A research in this case can provide a better understanding and an option of inserts with less cost than usually applied ceramic and CBN (cubic boron nitride) inserts. Thus, the objective is to investigate the tool-life of ISO P and ISO S grade coated carbide inserts and average roughness (Ra) of the machined surface generated with these tools in the hard turning of AISI 4140 steel under dry and minimum-quantity of lubrication (MQL) conditions. Comparing the ISO P and ISO S grades tool life in two different cutting speed levels (60 and 120 m/min), the higher cutting speed generated the lowest Ra values. Relating the lubri-cooling conditions, dry turning resulted in lower Ra values. When the tool nose wear does not change during the passes, the Ra remains constant. In addition, ISO S grade coated carbide insert has shown a possibility for this hard turning due to the low tool nose wear at a relatively high cutting speed.
id UFRGS-2_7f27ef5030ed2befda0961a0e4a62a36
oai_identifier_str oai:www.lume.ufrgs.br:10183/212751
network_acronym_str UFRGS-2
network_name_str Repositório Institucional da UFRGS
repository_id_str
spelling Polly, Matheus dos SantosMayrhofer, AmáliaSouza, André João de2020-08-08T03:46:13Z20200718-3305http://hdl.handle.net/10183/212751001115170The literature review shows few studies concerning the turning of hardened steels using carbide tools. A research in this case can provide a better understanding and an option of inserts with less cost than usually applied ceramic and CBN (cubic boron nitride) inserts. Thus, the objective is to investigate the tool-life of ISO P and ISO S grade coated carbide inserts and average roughness (Ra) of the machined surface generated with these tools in the hard turning of AISI 4140 steel under dry and minimum-quantity of lubrication (MQL) conditions. Comparing the ISO P and ISO S grades tool life in two different cutting speed levels (60 and 120 m/min), the higher cutting speed generated the lowest Ra values. Relating the lubri-cooling conditions, dry turning resulted in lower Ra values. When the tool nose wear does not change during the passes, the Ra remains constant. In addition, ISO S grade coated carbide insert has shown a possibility for this hard turning due to the low tool nose wear at a relatively high cutting speed.La revisión de la literatura muestra que existen pocos estudios sobre el torneado de los aceros endurecidos utilizando herramientas de metal duro. Una investigación en este caso puede proporcionar una mejor comprensión y la opción de reducir costo es usando los insertos de cerámica y CBN (nitruro de boro cúbico). Por tanto, el objetivo es investigar la vida útil de insertos de metal duro con recubrimiento calidades ISO P e ISO S y la rugosidad media (Ra) de la superficie mecanizada con estas herramientas en el torneado duro del acero AISI 4140 en las condiciones en seco y con una cantidad mínima de lubricante (MQL). En la comparación de la vida de las herramientas ISO P e ISO S en dos niveles de velocidades de corte (60 y 120 m/min), para la mayor velocidad de corte se generaron los valores más bajos de Ra. Al relacionar las condiciones de lubri-refrigeración, los valores más bajos de Ra resultaron con el torneado en seco. Cuando el desgaste de la punta de la herramienta no cambia durante los pases, el valor de Ra permanece constante. Además, el inserto de metal duro con recubrimiento calidad ISO S ha mostrado la posibilidad de usar en el torneado duro debido al bajo desgaste de la punta de la herramienta en una velocidad de corte relativamente alta.application/pdfengIngeniare: revista chilena de ingeniería [recurso eletrônico]. Arica, Chile. Vol. 28, no. 1 (Mar. 2020), p. 95-105AçoFerramentasMetais durosRugosidade de superfícieDesgasteHardened AISI 4140 steelCoated carbide toolsSurface roughnessTool nose wearAcero AISI 4140 endurecidoHerramientas de metal duro con recubrimientoRugosidad superficialDesgaste de la punta de la herramientaPerformance of ISO P and ISO S carbide tools in hard turning of AISI 4140 under dry and MQL conditionsRendimiento de las herramientas de metal duro ISO P e ISO S en el torneado de AISI 4140 endurecido en condiciones seco y con MQL Estrangeiroinfo:eu-repo/semantics/articleinfo:eu-repo/semantics/publishedVersioninfo:eu-repo/semantics/openAccessreponame:Repositório Institucional da UFRGSinstname:Universidade Federal do Rio Grande do Sul (UFRGS)instacron:UFRGSTEXT001115170.pdf.txt001115170.pdf.txtExtracted Texttext/plain33718http://www.lume.ufrgs.br/bitstream/10183/212751/2/001115170.pdf.txt2b1b1f48da21f980a3e6559a79975920MD52ORIGINAL001115170.pdfTexto completo (inglês)application/pdf1368068http://www.lume.ufrgs.br/bitstream/10183/212751/1/001115170.pdffc771bd691c8397aafbdc8ddc9b0e2d6MD5110183/2127512021-05-26 04:29:36.62146oai:www.lume.ufrgs.br:10183/212751Repositório de PublicaçõesPUBhttps://lume.ufrgs.br/oai/requestopendoar:2021-05-26T07:29:36Repositório Institucional da UFRGS - Universidade Federal do Rio Grande do Sul (UFRGS)false
dc.title.pt_BR.fl_str_mv Performance of ISO P and ISO S carbide tools in hard turning of AISI 4140 under dry and MQL conditions
dc.title.alternative.es.fl_str_mv Rendimiento de las herramientas de metal duro ISO P e ISO S en el torneado de AISI 4140 endurecido en condiciones seco y con MQL
title Performance of ISO P and ISO S carbide tools in hard turning of AISI 4140 under dry and MQL conditions
spellingShingle Performance of ISO P and ISO S carbide tools in hard turning of AISI 4140 under dry and MQL conditions
Polly, Matheus dos Santos
Aço
Ferramentas
Metais duros
Rugosidade de superfície
Desgaste
Hardened AISI 4140 steel
Coated carbide tools
Surface roughness
Tool nose wear
Acero AISI 4140 endurecido
Herramientas de metal duro con recubrimiento
Rugosidad superficial
Desgaste de la punta de la herramienta
title_short Performance of ISO P and ISO S carbide tools in hard turning of AISI 4140 under dry and MQL conditions
title_full Performance of ISO P and ISO S carbide tools in hard turning of AISI 4140 under dry and MQL conditions
title_fullStr Performance of ISO P and ISO S carbide tools in hard turning of AISI 4140 under dry and MQL conditions
title_full_unstemmed Performance of ISO P and ISO S carbide tools in hard turning of AISI 4140 under dry and MQL conditions
title_sort Performance of ISO P and ISO S carbide tools in hard turning of AISI 4140 under dry and MQL conditions
author Polly, Matheus dos Santos
author_facet Polly, Matheus dos Santos
Mayrhofer, Amália
Souza, André João de
author_role author
author2 Mayrhofer, Amália
Souza, André João de
author2_role author
author
dc.contributor.author.fl_str_mv Polly, Matheus dos Santos
Mayrhofer, Amália
Souza, André João de
dc.subject.por.fl_str_mv Aço
Ferramentas
Metais duros
Rugosidade de superfície
Desgaste
topic Aço
Ferramentas
Metais duros
Rugosidade de superfície
Desgaste
Hardened AISI 4140 steel
Coated carbide tools
Surface roughness
Tool nose wear
Acero AISI 4140 endurecido
Herramientas de metal duro con recubrimiento
Rugosidad superficial
Desgaste de la punta de la herramienta
dc.subject.eng.fl_str_mv Hardened AISI 4140 steel
Coated carbide tools
Surface roughness
Tool nose wear
dc.subject.spa.fl_str_mv Acero AISI 4140 endurecido
Herramientas de metal duro con recubrimiento
Rugosidad superficial
Desgaste de la punta de la herramienta
description The literature review shows few studies concerning the turning of hardened steels using carbide tools. A research in this case can provide a better understanding and an option of inserts with less cost than usually applied ceramic and CBN (cubic boron nitride) inserts. Thus, the objective is to investigate the tool-life of ISO P and ISO S grade coated carbide inserts and average roughness (Ra) of the machined surface generated with these tools in the hard turning of AISI 4140 steel under dry and minimum-quantity of lubrication (MQL) conditions. Comparing the ISO P and ISO S grades tool life in two different cutting speed levels (60 and 120 m/min), the higher cutting speed generated the lowest Ra values. Relating the lubri-cooling conditions, dry turning resulted in lower Ra values. When the tool nose wear does not change during the passes, the Ra remains constant. In addition, ISO S grade coated carbide insert has shown a possibility for this hard turning due to the low tool nose wear at a relatively high cutting speed.
publishDate 2020
dc.date.accessioned.fl_str_mv 2020-08-08T03:46:13Z
dc.date.issued.fl_str_mv 2020
dc.type.driver.fl_str_mv Estrangeiro
info:eu-repo/semantics/article
dc.type.status.fl_str_mv info:eu-repo/semantics/publishedVersion
format article
status_str publishedVersion
dc.identifier.uri.fl_str_mv http://hdl.handle.net/10183/212751
dc.identifier.issn.pt_BR.fl_str_mv 0718-3305
dc.identifier.nrb.pt_BR.fl_str_mv 001115170
identifier_str_mv 0718-3305
001115170
url http://hdl.handle.net/10183/212751
dc.language.iso.fl_str_mv eng
language eng
dc.relation.ispartof.pt_BR.fl_str_mv Ingeniare: revista chilena de ingeniería [recurso eletrônico]. Arica, Chile. Vol. 28, no. 1 (Mar. 2020), p. 95-105
dc.rights.driver.fl_str_mv info:eu-repo/semantics/openAccess
eu_rights_str_mv openAccess
dc.format.none.fl_str_mv application/pdf
dc.source.none.fl_str_mv reponame:Repositório Institucional da UFRGS
instname:Universidade Federal do Rio Grande do Sul (UFRGS)
instacron:UFRGS
instname_str Universidade Federal do Rio Grande do Sul (UFRGS)
instacron_str UFRGS
institution UFRGS
reponame_str Repositório Institucional da UFRGS
collection Repositório Institucional da UFRGS
bitstream.url.fl_str_mv http://www.lume.ufrgs.br/bitstream/10183/212751/2/001115170.pdf.txt
http://www.lume.ufrgs.br/bitstream/10183/212751/1/001115170.pdf
bitstream.checksum.fl_str_mv 2b1b1f48da21f980a3e6559a79975920
fc771bd691c8397aafbdc8ddc9b0e2d6
bitstream.checksumAlgorithm.fl_str_mv MD5
MD5
repository.name.fl_str_mv Repositório Institucional da UFRGS - Universidade Federal do Rio Grande do Sul (UFRGS)
repository.mail.fl_str_mv
_version_ 1815447718807470080

Registros relacionados