Avaliação tribológica dos polímeros NBR, PTFE e PTFE gravitado em contato com aço AISI 52100
Autor(a) principal: | |
---|---|
Data de Publicação: | 2009 |
Tipo de documento: | Dissertação |
Idioma: | por |
Título da fonte: | Repositório Institucional da UFRN |
Texto Completo: | https://repositorio.ufrn.br/jspui/handle/123456789/15591 |
Resumo: | Low cost seals are made of NBR, Nitrile Butadiene Rubber, a family of unsaturated copolymers that is higher resistant to oils the more content of nitrile have in its composition, although lower its flexibility. In Petroleum Engineering, NBR seal wear can cause fluid leakage and environmental damages, promoting an increasing demand for academic knowledge about polymeric materials candidate to seals submitted to sliding contacts to metal surfaces. This investigation aimed to evaluate tribological responses of a commercial NBR, hardness 73 ± 5 Sh A, polytetrafluoroethylene (PTFE), hardness 60 ± 4 HRE and PTFE with graphite, 68 ± 6 HRE. The testings were performed on a sliding tribometer conceived to explore the tribological performance of stationary polymer plane coupons submitted to rotational cylinder contact surface of steel AISI 52100, 20 ± 1 HRC Hardness, under dry and lubricated (oil SAE 15W40) conditions. After screening testings, the normal load, relative velocity and sliding distance were 3.15 N, 0.8 m/s and 3.2 km, respectively. The temperatures were collected over distances of 3.0±0.5 mm and 750±50 mm far from the contact to evaluate the heating in this referential zone due to contact sliding friction by two thermocouples K type. The polymers were characterized through Thermogravimetric Analysis (TGA), Differential Scanning Calorimetry (DSC) and Dynamic Mechanical Analysis (DMA). The wear mechanisms of the polymer surfaces were analyzed by Scanning Electron Microscopy (SEM) and EDS (Energy-Dispersive X-ray Spectroscopy). NBR referred to the higher values of heating, suggesting higher sliding friction. PTFE and PTFE with graphite showed lower heating, attributed to the delamination mechanism |
id |
UFRN_8af0c724893b645393ead212050f13c3 |
---|---|
oai_identifier_str |
oai:https://repositorio.ufrn.br:123456789/15591 |
network_acronym_str |
UFRN |
network_name_str |
Repositório Institucional da UFRN |
repository_id_str |
|
spelling |
Santana, Janaina Silva dehttp://lattes.cnpq.br/5262844608328752http://lattes.cnpq.br/3206952338356447Alves Júnior, Clodomirohttp://lattes.cnpq.br/7441669258580942Silva, Ademir Oliveira dahttp://lattes.cnpq.br/3511004608337461Lima, José de Anchietahttp://lattes.cnpq.br/0742445504420593Medeiros, João Telésforo Nóbrega de2014-12-17T14:57:54Z2010-03-242014-12-17T14:57:54Z2009-10-02SANTANA, Janaina Silva de. Avaliação tribológica dos polímeros NBR, PTFE e PTFE gravitado em contato com aço AISI 52100. 2009. 89 f. Dissertação (Mestrado em Tecnologia de Materiais; Projetos Mecânicos; Termociências) - Universidade Federal do Rio Grande do Norte, Natal, 2009.https://repositorio.ufrn.br/jspui/handle/123456789/15591Low cost seals are made of NBR, Nitrile Butadiene Rubber, a family of unsaturated copolymers that is higher resistant to oils the more content of nitrile have in its composition, although lower its flexibility. In Petroleum Engineering, NBR seal wear can cause fluid leakage and environmental damages, promoting an increasing demand for academic knowledge about polymeric materials candidate to seals submitted to sliding contacts to metal surfaces. This investigation aimed to evaluate tribological responses of a commercial NBR, hardness 73 ± 5 Sh A, polytetrafluoroethylene (PTFE), hardness 60 ± 4 HRE and PTFE with graphite, 68 ± 6 HRE. The testings were performed on a sliding tribometer conceived to explore the tribological performance of stationary polymer plane coupons submitted to rotational cylinder contact surface of steel AISI 52100, 20 ± 1 HRC Hardness, under dry and lubricated (oil SAE 15W40) conditions. After screening testings, the normal load, relative velocity and sliding distance were 3.15 N, 0.8 m/s and 3.2 km, respectively. The temperatures were collected over distances of 3.0±0.5 mm and 750±50 mm far from the contact to evaluate the heating in this referential zone due to contact sliding friction by two thermocouples K type. The polymers were characterized through Thermogravimetric Analysis (TGA), Differential Scanning Calorimetry (DSC) and Dynamic Mechanical Analysis (DMA). The wear mechanisms of the polymer surfaces were analyzed by Scanning Electron Microscopy (SEM) and EDS (Energy-Dispersive X-ray Spectroscopy). NBR referred to the higher values of heating, suggesting higher sliding friction. PTFE and PTFE with graphite showed lower heating, attributed to the delamination mechanismRetentores de baixo custo são comercialmente disponíveis de NBR, copolímeros insaturados de borrachas de nitrilo-butadieno que são mais resistentes aos óleos quanto mais altos forem seus teores de nitrila, à custa de uma menor flexibilidade. Em Engenharia de Petróleo, o desgaste dos retentores de NBR causa vazamento de fluidos e danos ambientais, provocando uma crescente demanda de conhecimento acadêmico sobre materiais poliméricos candidatos a retentor submetidos a contatos de deslizamento com superfícies de metal. Este trabalho objetivou avaliar respostas tribológicas de três polímeros comercialmente disponíveis, NBR, dureza 73 ± 5 Sh A, polytetrafluoroethylene (PTFE), dureza 60 ± 4 HRE e PTFE com grafite, 68 ± 6 HRE. Os ensaios foram realizados em um tribômetro de deslizamento concebido para explorar o desempenho tribológico de corpos-de-prova poliméricos estacionários de superfície plana submetidos a um contato seco ou lubrificado (óleo SAE 15W40) de uma superfície rotativa cilíndrica de aço 52100, dureza 20 ± 1 HRC. A carga normal, a velocidade relativa e a distância de deslizamento foram, respectivamente, 3,15 N, 0,8 m/s e 3,2 km, determinadas após ensaios exploratórios iniciais. As temperaturas foram medidas por dois termopares tipo K a 3,0±0,5 mm e 750±50 mm de distância do contato para avaliar-se o aquecimento em uma mesma região devido ao atrito de deslizamento no contato. Os polímeros foram caracterizados através de Análises Termogravimétricas (TGA), Calorimetria Diferencial Exploratória (DSC) e Análises Dinâmico-Mecânica (DMA). Os mecanismos de desgaste das superfícies dos polímeros foram analisados por Microscopia Eletrônica de Varredura (MEV) e EDS (Espectroscopia por Energia Dispersiva de Raios-X). NBR apresentou os maiores valores de aquecimento, sugerindo maior atrito de deslizamento. PTFE e PTFE grafitado apresentaram um menor aquecimento, atribuído ao mecanismo de desgaste por delaminaçãoCoordenação de Aperfeiçoamento de Pessoal de Nível Superiorapplication/pdfporUniversidade Federal do Rio Grande do NortePrograma de Pós-Graduação em Engenharia MecânicaUFRNBRTecnologia de Materiais; Projetos Mecânicos; TermociênciasTribologiaPolímerosDesgasteRetentoresPTFENBRPTFE grafitadoAço AISI 52100TribologyPolymersWearSealsPTFENBRPTFE-graphiteAISI 52100 SteelCNPQ::ENGENHARIAS::ENGENHARIA MECANICAAvaliação tribológica dos polímeros NBR, PTFE e PTFE gravitado em contato com aço AISI 52100info:eu-repo/semantics/publishedVersioninfo:eu-repo/semantics/masterThesisinfo:eu-repo/semantics/openAccessreponame:Repositório Institucional da UFRNinstname:Universidade Federal do Rio Grande do Norte (UFRN)instacron:UFRNORIGINALJanainaSS.pdfapplication/pdf6774864https://repositorio.ufrn.br/bitstream/123456789/15591/1/JanainaSS.pdf445b5e932b89fcc09c4b97403b959e26MD51TEXTJanainaSS.pdf.txtJanainaSS.pdf.txtExtracted texttext/plain135126https://repositorio.ufrn.br/bitstream/123456789/15591/6/JanainaSS.pdf.txtffad27b0f104b6e70d03b43e3c9206aeMD56THUMBNAILJanainaSS.pdf.jpgJanainaSS.pdf.jpgIM Thumbnailimage/jpeg2881https://repositorio.ufrn.br/bitstream/123456789/15591/7/JanainaSS.pdf.jpg9270c3052bdf4fb182c8712c8779263fMD57123456789/155912017-11-01 11:53:38.607oai:https://repositorio.ufrn.br:123456789/15591Repositório de PublicaçõesPUBhttp://repositorio.ufrn.br/oai/opendoar:2017-11-01T14:53:38Repositório Institucional da UFRN - Universidade Federal do Rio Grande do Norte (UFRN)false |
dc.title.por.fl_str_mv |
Avaliação tribológica dos polímeros NBR, PTFE e PTFE gravitado em contato com aço AISI 52100 |
title |
Avaliação tribológica dos polímeros NBR, PTFE e PTFE gravitado em contato com aço AISI 52100 |
spellingShingle |
Avaliação tribológica dos polímeros NBR, PTFE e PTFE gravitado em contato com aço AISI 52100 Santana, Janaina Silva de Tribologia Polímeros Desgaste Retentores PTFE NBR PTFE grafitado Aço AISI 52100 Tribology Polymers Wear Seals PTFE NBR PTFE-graphite AISI 52100 Steel CNPQ::ENGENHARIAS::ENGENHARIA MECANICA |
title_short |
Avaliação tribológica dos polímeros NBR, PTFE e PTFE gravitado em contato com aço AISI 52100 |
title_full |
Avaliação tribológica dos polímeros NBR, PTFE e PTFE gravitado em contato com aço AISI 52100 |
title_fullStr |
Avaliação tribológica dos polímeros NBR, PTFE e PTFE gravitado em contato com aço AISI 52100 |
title_full_unstemmed |
Avaliação tribológica dos polímeros NBR, PTFE e PTFE gravitado em contato com aço AISI 52100 |
title_sort |
Avaliação tribológica dos polímeros NBR, PTFE e PTFE gravitado em contato com aço AISI 52100 |
author |
Santana, Janaina Silva de |
author_facet |
Santana, Janaina Silva de |
author_role |
author |
dc.contributor.authorID.por.fl_str_mv |
|
dc.contributor.authorLattes.por.fl_str_mv |
http://lattes.cnpq.br/5262844608328752 |
dc.contributor.advisorID.por.fl_str_mv |
|
dc.contributor.advisorLattes.por.fl_str_mv |
http://lattes.cnpq.br/3206952338356447 |
dc.contributor.advisor-co1ID.por.fl_str_mv |
|
dc.contributor.referees1.pt_BR.fl_str_mv |
Silva, Ademir Oliveira da |
dc.contributor.referees1ID.por.fl_str_mv |
|
dc.contributor.referees1Lattes.por.fl_str_mv |
http://lattes.cnpq.br/3511004608337461 |
dc.contributor.referees2.pt_BR.fl_str_mv |
Lima, José de Anchieta |
dc.contributor.referees2ID.por.fl_str_mv |
|
dc.contributor.referees2Lattes.por.fl_str_mv |
http://lattes.cnpq.br/0742445504420593 |
dc.contributor.author.fl_str_mv |
Santana, Janaina Silva de |
dc.contributor.advisor-co1.fl_str_mv |
Alves Júnior, Clodomiro |
dc.contributor.advisor-co1Lattes.fl_str_mv |
http://lattes.cnpq.br/7441669258580942 |
dc.contributor.advisor1.fl_str_mv |
Medeiros, João Telésforo Nóbrega de |
contributor_str_mv |
Alves Júnior, Clodomiro Medeiros, João Telésforo Nóbrega de |
dc.subject.por.fl_str_mv |
Tribologia Polímeros Desgaste Retentores PTFE NBR PTFE grafitado Aço AISI 52100 |
topic |
Tribologia Polímeros Desgaste Retentores PTFE NBR PTFE grafitado Aço AISI 52100 Tribology Polymers Wear Seals PTFE NBR PTFE-graphite AISI 52100 Steel CNPQ::ENGENHARIAS::ENGENHARIA MECANICA |
dc.subject.eng.fl_str_mv |
Tribology Polymers Wear Seals PTFE NBR PTFE-graphite AISI 52100 Steel |
dc.subject.cnpq.fl_str_mv |
CNPQ::ENGENHARIAS::ENGENHARIA MECANICA |
description |
Low cost seals are made of NBR, Nitrile Butadiene Rubber, a family of unsaturated copolymers that is higher resistant to oils the more content of nitrile have in its composition, although lower its flexibility. In Petroleum Engineering, NBR seal wear can cause fluid leakage and environmental damages, promoting an increasing demand for academic knowledge about polymeric materials candidate to seals submitted to sliding contacts to metal surfaces. This investigation aimed to evaluate tribological responses of a commercial NBR, hardness 73 ± 5 Sh A, polytetrafluoroethylene (PTFE), hardness 60 ± 4 HRE and PTFE with graphite, 68 ± 6 HRE. The testings were performed on a sliding tribometer conceived to explore the tribological performance of stationary polymer plane coupons submitted to rotational cylinder contact surface of steel AISI 52100, 20 ± 1 HRC Hardness, under dry and lubricated (oil SAE 15W40) conditions. After screening testings, the normal load, relative velocity and sliding distance were 3.15 N, 0.8 m/s and 3.2 km, respectively. The temperatures were collected over distances of 3.0±0.5 mm and 750±50 mm far from the contact to evaluate the heating in this referential zone due to contact sliding friction by two thermocouples K type. The polymers were characterized through Thermogravimetric Analysis (TGA), Differential Scanning Calorimetry (DSC) and Dynamic Mechanical Analysis (DMA). The wear mechanisms of the polymer surfaces were analyzed by Scanning Electron Microscopy (SEM) and EDS (Energy-Dispersive X-ray Spectroscopy). NBR referred to the higher values of heating, suggesting higher sliding friction. PTFE and PTFE with graphite showed lower heating, attributed to the delamination mechanism |
publishDate |
2009 |
dc.date.issued.fl_str_mv |
2009-10-02 |
dc.date.available.fl_str_mv |
2010-03-24 2014-12-17T14:57:54Z |
dc.date.accessioned.fl_str_mv |
2014-12-17T14:57:54Z |
dc.type.status.fl_str_mv |
info:eu-repo/semantics/publishedVersion |
dc.type.driver.fl_str_mv |
info:eu-repo/semantics/masterThesis |
format |
masterThesis |
status_str |
publishedVersion |
dc.identifier.citation.fl_str_mv |
SANTANA, Janaina Silva de. Avaliação tribológica dos polímeros NBR, PTFE e PTFE gravitado em contato com aço AISI 52100. 2009. 89 f. Dissertação (Mestrado em Tecnologia de Materiais; Projetos Mecânicos; Termociências) - Universidade Federal do Rio Grande do Norte, Natal, 2009. |
dc.identifier.uri.fl_str_mv |
https://repositorio.ufrn.br/jspui/handle/123456789/15591 |
identifier_str_mv |
SANTANA, Janaina Silva de. Avaliação tribológica dos polímeros NBR, PTFE e PTFE gravitado em contato com aço AISI 52100. 2009. 89 f. Dissertação (Mestrado em Tecnologia de Materiais; Projetos Mecânicos; Termociências) - Universidade Federal do Rio Grande do Norte, Natal, 2009. |
url |
https://repositorio.ufrn.br/jspui/handle/123456789/15591 |
dc.language.iso.fl_str_mv |
por |
language |
por |
dc.rights.driver.fl_str_mv |
info:eu-repo/semantics/openAccess |
eu_rights_str_mv |
openAccess |
dc.format.none.fl_str_mv |
application/pdf |
dc.publisher.none.fl_str_mv |
Universidade Federal do Rio Grande do Norte |
dc.publisher.program.fl_str_mv |
Programa de Pós-Graduação em Engenharia Mecânica |
dc.publisher.initials.fl_str_mv |
UFRN |
dc.publisher.country.fl_str_mv |
BR |
dc.publisher.department.fl_str_mv |
Tecnologia de Materiais; Projetos Mecânicos; Termociências |
publisher.none.fl_str_mv |
Universidade Federal do Rio Grande do Norte |
dc.source.none.fl_str_mv |
reponame:Repositório Institucional da UFRN instname:Universidade Federal do Rio Grande do Norte (UFRN) instacron:UFRN |
instname_str |
Universidade Federal do Rio Grande do Norte (UFRN) |
instacron_str |
UFRN |
institution |
UFRN |
reponame_str |
Repositório Institucional da UFRN |
collection |
Repositório Institucional da UFRN |
bitstream.url.fl_str_mv |
https://repositorio.ufrn.br/bitstream/123456789/15591/1/JanainaSS.pdf https://repositorio.ufrn.br/bitstream/123456789/15591/6/JanainaSS.pdf.txt https://repositorio.ufrn.br/bitstream/123456789/15591/7/JanainaSS.pdf.jpg |
bitstream.checksum.fl_str_mv |
445b5e932b89fcc09c4b97403b959e26 ffad27b0f104b6e70d03b43e3c9206ae 9270c3052bdf4fb182c8712c8779263f |
bitstream.checksumAlgorithm.fl_str_mv |
MD5 MD5 MD5 |
repository.name.fl_str_mv |
Repositório Institucional da UFRN - Universidade Federal do Rio Grande do Norte (UFRN) |
repository.mail.fl_str_mv |
|
_version_ |
1802117589321646080 |