Efeito da usinagem, do ciclo térmico de glazeamento e do condicionamento ácido na resistência flexural de uma cerâmica vítrea
Autor(a) principal: | |
---|---|
Data de Publicação: | 2013 |
Tipo de documento: | Dissertação |
Idioma: | por |
Título da fonte: | Manancial - Repositório Digital da UFSM |
Texto Completo: | http://repositorio.ufsm.br/handle/1/6113 |
Resumo: | The aim of this study was to evaluate the effect of hard machining, thermal cycle for glazing and acid etching on the surface roughness and flexural strength of a leucite glass-ceramic. Additionally, it was investigated whether the roughness after machining would be influenced by the machining order and by the pair of burs employed. Six pair of burs were used to produce 144 discs by automated machining, which were divided into groups (n=24): 1) machining (M); 2) machining and heat treatment (MH); 3) machining and acid etching (MA); 4) machining, heat treatment and acid etching (MHA); 5) machining and polishing (MP); 6) machining, polishing and acid etching (MPA). The roughness after each treatment was measured using a contact profilometer. The discs were submitted to a piston-on-three ball flexure test (ISO 6872/2008). Weibull analysis was used to compare the characteristic strength (σ0) and Weibull modulus (m) of the groups. The effect of the treatments, machining order and pair of burs on the surface roughness of the specimens was analyzed. Machining reduced the σ0 when compared to polishing. The polishing protocol was able to eliminate the defects introduced by machining, which was observed by means of scanning electron microscopy. The heat treatment did not alter the roughness, but reduced the σ0 and created amorphous material on the ceramic surface, as shown by the x-ray diffraction. Acid etching increased roughness, without reduce σ0. The Weibull modulus did not differ significantly among the groups, which means that all the treatments resulted in similar defects distribution. Spearman s coefficient (rs) indicated strong and significant correlation between machining order and roughness (rsRa = -0,66; rsRz = -0,73). The roughness after machining differed significantly according to the pair of burs employed (p<0,05). Thus, hard machining and thermal cycle for glaze demonstrated a negative effect on the ceramic strength, as opposed to acid etching, which does not appear to affect the flexural strength of the material. Variability in the roughness data could be expected after machining, since the Ra and Rz values seem to be influenced by the machining order and the pair of burs employed. |
id |
UFSM_4cd3b36c96049fb8d8bf11525d53e0a2 |
---|---|
oai_identifier_str |
oai:repositorio.ufsm.br:1/6113 |
network_acronym_str |
UFSM |
network_name_str |
Manancial - Repositório Digital da UFSM |
repository_id_str |
|
spelling |
Efeito da usinagem, do ciclo térmico de glazeamento e do condicionamento ácido na resistência flexural de uma cerâmica vítreaEfect of machining, thermal cycle for glazing and acid etching in the flexural strength of a glass-ceramicCerâmica vítreaLeucitaCAD/CAMTratamento térmicoÁcido hidrofluorídricoRugosidadeResistência flexural biaxialGlass-ceramicLeuciteHeat treatmentHydrofluoric acidRoughnessBiaxial flexural strengthCNPQ::CIENCIAS DA SAUDE::ODONTOLOGIAThe aim of this study was to evaluate the effect of hard machining, thermal cycle for glazing and acid etching on the surface roughness and flexural strength of a leucite glass-ceramic. Additionally, it was investigated whether the roughness after machining would be influenced by the machining order and by the pair of burs employed. Six pair of burs were used to produce 144 discs by automated machining, which were divided into groups (n=24): 1) machining (M); 2) machining and heat treatment (MH); 3) machining and acid etching (MA); 4) machining, heat treatment and acid etching (MHA); 5) machining and polishing (MP); 6) machining, polishing and acid etching (MPA). The roughness after each treatment was measured using a contact profilometer. The discs were submitted to a piston-on-three ball flexure test (ISO 6872/2008). Weibull analysis was used to compare the characteristic strength (σ0) and Weibull modulus (m) of the groups. The effect of the treatments, machining order and pair of burs on the surface roughness of the specimens was analyzed. Machining reduced the σ0 when compared to polishing. The polishing protocol was able to eliminate the defects introduced by machining, which was observed by means of scanning electron microscopy. The heat treatment did not alter the roughness, but reduced the σ0 and created amorphous material on the ceramic surface, as shown by the x-ray diffraction. Acid etching increased roughness, without reduce σ0. The Weibull modulus did not differ significantly among the groups, which means that all the treatments resulted in similar defects distribution. Spearman s coefficient (rs) indicated strong and significant correlation between machining order and roughness (rsRa = -0,66; rsRz = -0,73). The roughness after machining differed significantly according to the pair of burs employed (p<0,05). Thus, hard machining and thermal cycle for glaze demonstrated a negative effect on the ceramic strength, as opposed to acid etching, which does not appear to affect the flexural strength of the material. Variability in the roughness data could be expected after machining, since the Ra and Rz values seem to be influenced by the machining order and the pair of burs employed.Fundação de Amparo a Pesquisa no Estado do Rio Grande do SulO presente trabalho objetivou avaliar o efeito da usinagem de corte duro, do ciclo térmico de glazeamento e do condicionamento ácido na rugosidade superficial e na resistência flexural de uma cerâmica vítrea reforçada por leucita. Adicionalmente, buscou-se investigar se a rugosidade após usinagem seria influenciada pela ordem de usinagem e pelo par de brocas utilizado. Seis pares de brocas foram empregados na confecção de 144 discos por usinagem automatizada, os quais foram divididos nos grupos (n=24): 1) usinagem (U); 2) usinagem e tratamento térmico (UT); 3) usinagem e condicionamento ácido (UCA); 4) usinagem, tratamento térmico e condicionamento ácido (UTCA); 5) usinagem e polimento (UP); 6) usinagem, polimento e condicionamento ácido (UPCA). A rugosidade (Ra e Rz) após os tratamentos foi mensurada em perfilômetro de contato. Os discos foram submetidos ao ensaio de flexão biaxial piston-on-three ball (ISO 6872/2008). Análise de Weibull foi utilizada para comparar-se os grupos quanto à resistência característica (σ0) e ao módulo de Weibull (m). Os efeitos dos tratamentos, da ordem de usinagem e dos diferentes pares de brocas sobre a rugosidade superficial dos corpos de prova foi estudado. A usinagem reduziu a σ0, quando comparada ao grupo UP. O protocolo de polimento adotado foi capaz de eliminar os defeitos oriundos da usinagem, o que foi verificado por meio de imagens em microscopia eletrônica de varredura. O tratamento térmico não alterou a rugosidade, mas reduziu a σ0 e ocasionou a formação de material amorfo na superfície da cerâmica, como mostrado pela difração de raios-x. O condicionamento ácido aumentou a rugosidade, sem alterar a σ0. O valor de m não diferiu significativamente entre os grupos, o que significa dizer que os tratamentos aplicados na cerâmica resultaram em distribuição similar de defeitos. Coeficiente de Spearman (rs) indicou correlação forte e significativa entre ordem de usinagem e rugosidade (rsRa = -0,66; rsRz = -0,73), a qual diferiu significativamente conforme o par de broca empregado para a usinagem (p<0,05). Sendo assim, a usinagem de corte duro e o ciclo térmico usado no glazeamento demostraram efeito negativo na resistência da cerâmica, em oposição ao condicionamento ácido, o qual parece não afetar a resistência do material. Variabilidade dos dados de rugosidade pode ser esperada após usinagem, uma vez que os valores de Ra e Rz parecem ser influenciados pela ordem de usinagem e pelo par de brocas utilizado.Universidade Federal de Santa MariaBROdontologiaUFSMPrograma de Pós-Graduação em Ciências OdontológicasMay, Liliana Gresslerhttp://lattes.cnpq.br/6812578163990395Borba, Márciahttp://lattes.cnpq.br/5230074566247388Jacques, Letícia Borgeshttp://lattes.cnpq.br/6588065834649820Fraga, Sara2014-07-212014-07-212013-07-31info:eu-repo/semantics/publishedVersioninfo:eu-repo/semantics/masterThesisapplication/pdfapplication/pdfFRAGA, Sara. Efect of machining, thermal cycle for glazing and acid etching in the flexural strength of a glass-ceramic. 2013. 73 f. Dissertação (Mestrado em Odontologia) - Universidade Federal de Santa Maria, Santa Maria, 2013.http://repositorio.ufsm.br/handle/1/6113porinfo:eu-repo/semantics/openAccessreponame:Manancial - Repositório Digital da UFSMinstname:Universidade Federal de Santa Maria (UFSM)instacron:UFSM2022-01-10T13:12:25Zoai:repositorio.ufsm.br:1/6113Biblioteca Digital de Teses e Dissertaçõeshttps://repositorio.ufsm.br/ONGhttps://repositorio.ufsm.br/oai/requestatendimento.sib@ufsm.br||tedebc@gmail.comopendoar:2022-01-10T13:12:25Manancial - Repositório Digital da UFSM - Universidade Federal de Santa Maria (UFSM)false |
dc.title.none.fl_str_mv |
Efeito da usinagem, do ciclo térmico de glazeamento e do condicionamento ácido na resistência flexural de uma cerâmica vítrea Efect of machining, thermal cycle for glazing and acid etching in the flexural strength of a glass-ceramic |
title |
Efeito da usinagem, do ciclo térmico de glazeamento e do condicionamento ácido na resistência flexural de uma cerâmica vítrea |
spellingShingle |
Efeito da usinagem, do ciclo térmico de glazeamento e do condicionamento ácido na resistência flexural de uma cerâmica vítrea Fraga, Sara Cerâmica vítrea Leucita CAD/CAM Tratamento térmico Ácido hidrofluorídrico Rugosidade Resistência flexural biaxial Glass-ceramic Leucite Heat treatment Hydrofluoric acid Roughness Biaxial flexural strength CNPQ::CIENCIAS DA SAUDE::ODONTOLOGIA |
title_short |
Efeito da usinagem, do ciclo térmico de glazeamento e do condicionamento ácido na resistência flexural de uma cerâmica vítrea |
title_full |
Efeito da usinagem, do ciclo térmico de glazeamento e do condicionamento ácido na resistência flexural de uma cerâmica vítrea |
title_fullStr |
Efeito da usinagem, do ciclo térmico de glazeamento e do condicionamento ácido na resistência flexural de uma cerâmica vítrea |
title_full_unstemmed |
Efeito da usinagem, do ciclo térmico de glazeamento e do condicionamento ácido na resistência flexural de uma cerâmica vítrea |
title_sort |
Efeito da usinagem, do ciclo térmico de glazeamento e do condicionamento ácido na resistência flexural de uma cerâmica vítrea |
author |
Fraga, Sara |
author_facet |
Fraga, Sara |
author_role |
author |
dc.contributor.none.fl_str_mv |
May, Liliana Gressler http://lattes.cnpq.br/6812578163990395 Borba, Márcia http://lattes.cnpq.br/5230074566247388 Jacques, Letícia Borges http://lattes.cnpq.br/6588065834649820 |
dc.contributor.author.fl_str_mv |
Fraga, Sara |
dc.subject.por.fl_str_mv |
Cerâmica vítrea Leucita CAD/CAM Tratamento térmico Ácido hidrofluorídrico Rugosidade Resistência flexural biaxial Glass-ceramic Leucite Heat treatment Hydrofluoric acid Roughness Biaxial flexural strength CNPQ::CIENCIAS DA SAUDE::ODONTOLOGIA |
topic |
Cerâmica vítrea Leucita CAD/CAM Tratamento térmico Ácido hidrofluorídrico Rugosidade Resistência flexural biaxial Glass-ceramic Leucite Heat treatment Hydrofluoric acid Roughness Biaxial flexural strength CNPQ::CIENCIAS DA SAUDE::ODONTOLOGIA |
description |
The aim of this study was to evaluate the effect of hard machining, thermal cycle for glazing and acid etching on the surface roughness and flexural strength of a leucite glass-ceramic. Additionally, it was investigated whether the roughness after machining would be influenced by the machining order and by the pair of burs employed. Six pair of burs were used to produce 144 discs by automated machining, which were divided into groups (n=24): 1) machining (M); 2) machining and heat treatment (MH); 3) machining and acid etching (MA); 4) machining, heat treatment and acid etching (MHA); 5) machining and polishing (MP); 6) machining, polishing and acid etching (MPA). The roughness after each treatment was measured using a contact profilometer. The discs were submitted to a piston-on-three ball flexure test (ISO 6872/2008). Weibull analysis was used to compare the characteristic strength (σ0) and Weibull modulus (m) of the groups. The effect of the treatments, machining order and pair of burs on the surface roughness of the specimens was analyzed. Machining reduced the σ0 when compared to polishing. The polishing protocol was able to eliminate the defects introduced by machining, which was observed by means of scanning electron microscopy. The heat treatment did not alter the roughness, but reduced the σ0 and created amorphous material on the ceramic surface, as shown by the x-ray diffraction. Acid etching increased roughness, without reduce σ0. The Weibull modulus did not differ significantly among the groups, which means that all the treatments resulted in similar defects distribution. Spearman s coefficient (rs) indicated strong and significant correlation between machining order and roughness (rsRa = -0,66; rsRz = -0,73). The roughness after machining differed significantly according to the pair of burs employed (p<0,05). Thus, hard machining and thermal cycle for glaze demonstrated a negative effect on the ceramic strength, as opposed to acid etching, which does not appear to affect the flexural strength of the material. Variability in the roughness data could be expected after machining, since the Ra and Rz values seem to be influenced by the machining order and the pair of burs employed. |
publishDate |
2013 |
dc.date.none.fl_str_mv |
2013-07-31 2014-07-21 2014-07-21 |
dc.type.status.fl_str_mv |
info:eu-repo/semantics/publishedVersion |
dc.type.driver.fl_str_mv |
info:eu-repo/semantics/masterThesis |
format |
masterThesis |
status_str |
publishedVersion |
dc.identifier.uri.fl_str_mv |
FRAGA, Sara. Efect of machining, thermal cycle for glazing and acid etching in the flexural strength of a glass-ceramic. 2013. 73 f. Dissertação (Mestrado em Odontologia) - Universidade Federal de Santa Maria, Santa Maria, 2013. http://repositorio.ufsm.br/handle/1/6113 |
identifier_str_mv |
FRAGA, Sara. Efect of machining, thermal cycle for glazing and acid etching in the flexural strength of a glass-ceramic. 2013. 73 f. Dissertação (Mestrado em Odontologia) - Universidade Federal de Santa Maria, Santa Maria, 2013. |
url |
http://repositorio.ufsm.br/handle/1/6113 |
dc.language.iso.fl_str_mv |
por |
language |
por |
dc.rights.driver.fl_str_mv |
info:eu-repo/semantics/openAccess |
eu_rights_str_mv |
openAccess |
dc.format.none.fl_str_mv |
application/pdf application/pdf |
dc.publisher.none.fl_str_mv |
Universidade Federal de Santa Maria BR Odontologia UFSM Programa de Pós-Graduação em Ciências Odontológicas |
publisher.none.fl_str_mv |
Universidade Federal de Santa Maria BR Odontologia UFSM Programa de Pós-Graduação em Ciências Odontológicas |
dc.source.none.fl_str_mv |
reponame:Manancial - Repositório Digital da UFSM instname:Universidade Federal de Santa Maria (UFSM) instacron:UFSM |
instname_str |
Universidade Federal de Santa Maria (UFSM) |
instacron_str |
UFSM |
institution |
UFSM |
reponame_str |
Manancial - Repositório Digital da UFSM |
collection |
Manancial - Repositório Digital da UFSM |
repository.name.fl_str_mv |
Manancial - Repositório Digital da UFSM - Universidade Federal de Santa Maria (UFSM) |
repository.mail.fl_str_mv |
atendimento.sib@ufsm.br||tedebc@gmail.com |
_version_ |
1805922016691224576 |