Influência do laser de diodo na evaporação do solvente de sistemas adesivos em dentina.
Autor(a) principal: | |
---|---|
Data de Publicação: | 2015 |
Tipo de documento: | Dissertação |
Idioma: | por |
Título da fonte: | Manancial - Repositório Digital da UFSM |
Texto Completo: | http://repositorio.ufsm.br/handle/1/6161 |
Resumo: | This study aimed to evaluate, in vitro, the influence of Diode Laser on the evaporation of adhesive systems solvent applied on the dentin. The groups were distributed in relation to the adhesive systems (Adper Single Bond 2, Adper Scotchbond Multi Purpose, Single Bond Universal, Clearfil SE Bond e Optibond All-in-one) and also to the technique for the evaporation of the solvent (air dry stream or Diode Laser). The degree of evaporation (GE) was determined through the measuring of mass loss through the gravimetric method in an analytical digital balance. To do so, a hundred human third molars had cavities class I made of following a pattern with the diamond burs # 4054 (KG Soresen, Barueri, SP, Brasil), under refrigeration, on which 10 μL were dispensed of each adhesive system, then one of the both techniques of solvent evaporation was applied: air dry stream, from a distance of 10 cm for each 5 seconds (control technique) or Diode Laser irradiated in a continuous mode perpendicularly and from a distance of 1 cm, in the power of 3 W in the interval of 30 seconds (experimental technique). To each one of the adhesive systems and to each one of the evaporation techniques ten monitoring repetitions were realized (n=10). Regarding the experimental technique, the measurements were realized from 5 to 5 seconds, up to 30 seconds. The variation between the initial mass (mi) and the final mass (mf) of the samples, respectively, before and after the application methods of evaporation proposed were turned into GE, by using the following equation: (mi-mf/mi)x100. In this way, to each time interval (5, 10, 15, 20, 25 and 30 seconds) it happened a calculated GE outcome. Those values were submitted to variance analysis (ANOVA) of two factors and Tukey s test as well. To the comparison between both of the evaporation techniques in each adhesive system a t-student test (α=5%) was realized. Basing on the obtained values of the GE, verified on the current study, it is possible to conclude that the irradiation with Diode Laser was capable of inducing the solvent evaporation of the tested adhesive systems, being superior to the control technique when used in the time of 30 seconds, excepted to the Optibond-all-in-one adhesive system. |
id |
UFSM_7f4926d13a8974c7b913cc8c19e6ebdb |
---|---|
oai_identifier_str |
oai:repositorio.ufsm.br:1/6161 |
network_acronym_str |
UFSM |
network_name_str |
Manancial - Repositório Digital da UFSM |
repository_id_str |
|
spelling |
Influência do laser de diodo na evaporação do solvente de sistemas adesivos em dentina.The influence of diode laser in evaporation of adhesive systems solvent in dentinEvaporaçãoSistema adesivoLaser de diodoEvaporationAdhesive systemDiode laserCNPQ::CIENCIAS DA SAUDE::ODONTOLOGIAThis study aimed to evaluate, in vitro, the influence of Diode Laser on the evaporation of adhesive systems solvent applied on the dentin. The groups were distributed in relation to the adhesive systems (Adper Single Bond 2, Adper Scotchbond Multi Purpose, Single Bond Universal, Clearfil SE Bond e Optibond All-in-one) and also to the technique for the evaporation of the solvent (air dry stream or Diode Laser). The degree of evaporation (GE) was determined through the measuring of mass loss through the gravimetric method in an analytical digital balance. To do so, a hundred human third molars had cavities class I made of following a pattern with the diamond burs # 4054 (KG Soresen, Barueri, SP, Brasil), under refrigeration, on which 10 μL were dispensed of each adhesive system, then one of the both techniques of solvent evaporation was applied: air dry stream, from a distance of 10 cm for each 5 seconds (control technique) or Diode Laser irradiated in a continuous mode perpendicularly and from a distance of 1 cm, in the power of 3 W in the interval of 30 seconds (experimental technique). To each one of the adhesive systems and to each one of the evaporation techniques ten monitoring repetitions were realized (n=10). Regarding the experimental technique, the measurements were realized from 5 to 5 seconds, up to 30 seconds. The variation between the initial mass (mi) and the final mass (mf) of the samples, respectively, before and after the application methods of evaporation proposed were turned into GE, by using the following equation: (mi-mf/mi)x100. In this way, to each time interval (5, 10, 15, 20, 25 and 30 seconds) it happened a calculated GE outcome. Those values were submitted to variance analysis (ANOVA) of two factors and Tukey s test as well. To the comparison between both of the evaporation techniques in each adhesive system a t-student test (α=5%) was realized. Basing on the obtained values of the GE, verified on the current study, it is possible to conclude that the irradiation with Diode Laser was capable of inducing the solvent evaporation of the tested adhesive systems, being superior to the control technique when used in the time of 30 seconds, excepted to the Optibond-all-in-one adhesive system.Este estudo objetivou avaliar, in vitro, a influência do Laser de Diodo sobre a evaporação do solvente de sistemas adesivos aplicados sobre dentina. Os grupos foram distribuídos em função dos sistemas adesivos (Adper Single Bond 2, Adper Scotchbond Multi Purpose, Single Bond Universal, Clearfil SE Bond e Optibond All-in-one) e da técnica para a evaporação do solvente (jato de ar ou Laser de Diodo). O grau de evaporação (GE) foi determinado através da mensuração da perda de massa pelo método gravimétrico. Para tal, 100 terceiros molares humanos tiveram cavidades classe I confeccionadas de forma padronizada com ponta diamantada em alta rotação (# 4054, KG Soresen, Barueri, SP, Brasil), sob refrigeração, nas quais foi dispensado 10 μL de cada sistema adesivo, seguido da aplicação de uma das técnicas de evaporação do solvente: jato de ar a uma distância de 10 cm por 5 segundos (técnica controle) ou Laser de Diodo irradiado em modo contínuo, perpendicularmente e a uma distância de 1 cm, na potência de 3W no tempo de 30 segundos (técnica experimental). Para cada um dos sistemas adesivos e para cada uma das técnicas de evaporação foram realizadas dez repetições de monitoramento (n=10). Para a técnica experimental as mensurações foram realizadas de 5 em 5 segundos, até 30 segundos. A variação entre massa inicial (mi) e final (mf) das amostras, respectivamente, antes e após a aplicação dos protocolos de evaporação propostos, foram transformadas em GE aplicando-se a seguinte equação: (mi-mf/mi)x100. Portanto, para cada intervalo de tempo, 5, 10, 15, 20, 25 e 30 segundos, houve um desfecho GE calculado. Os resultados foram submetidos à análise de variância (ANOVA) de dois fatores e teste de Tukey. Para comparação entre as técnicas de evaporação em cada sistema adesivo foi utilizado teste t-student (α = 5%).Com base nos valores obtidos do GE verificados no presente estudo, o laser provocou maior evaporação do solvente quando comparado ao Jato de ar, no tempo de 30 segundos, exceto para o sistema adesivo acetonado. Desta forma, a irradiação com Laser de Diodo foi capaz de provocar a evaporação do solvente dos sistemas adesivos testados, sendo superior à técnica controle quando utilizada no tempo de 30 segundos, exceto para o sistema adesivo Optibond-all-in-one.Universidade Federal de Santa MariaBROdontologiaUFSMPrograma de Pós-Graduação em Ciências OdontológicasSilveira, Bruno Lopes dahttp://lattes.cnpq.br/8477118220635736Rocha, Rachel de Oliveirahttp://lattes.cnpq.br/0239294008628766Becker, Anne Busshttp://lattes.cnpq.br/4794094513719948Pozzobon, Roselaine Terezinhahttp://lattes.cnpq.br/0725237903741859Chiattone, Tatiana Dalla Costa2016-02-182016-02-182015-06-29info:eu-repo/semantics/publishedVersioninfo:eu-repo/semantics/masterThesisapplication/pdfapplication/pdfCHIATTONE, Tatiana Dalla Costa. THE INFLUENCE OF DIODE LASER IN EVAPORATION OF ADHESIVE SYSTEMS SOLVENT IN DENTIN. 2015. 43 f. Dissertação (Mestrado em Odontologia) - Universidade Federal de Santa Maria, Santa Maria, 2015.http://repositorio.ufsm.br/handle/1/6161porinfo:eu-repo/semantics/openAccessreponame:Manancial - Repositório Digital da UFSMinstname:Universidade Federal de Santa Maria (UFSM)instacron:UFSM2021-10-28T13:33:35Zoai:repositorio.ufsm.br:1/6161Biblioteca Digital de Teses e Dissertaçõeshttps://repositorio.ufsm.br/ONGhttps://repositorio.ufsm.br/oai/requestatendimento.sib@ufsm.br||tedebc@gmail.comopendoar:2021-10-28T13:33:35Manancial - Repositório Digital da UFSM - Universidade Federal de Santa Maria (UFSM)false |
dc.title.none.fl_str_mv |
Influência do laser de diodo na evaporação do solvente de sistemas adesivos em dentina. The influence of diode laser in evaporation of adhesive systems solvent in dentin |
title |
Influência do laser de diodo na evaporação do solvente de sistemas adesivos em dentina. |
spellingShingle |
Influência do laser de diodo na evaporação do solvente de sistemas adesivos em dentina. Chiattone, Tatiana Dalla Costa Evaporação Sistema adesivo Laser de diodo Evaporation Adhesive system Diode laser CNPQ::CIENCIAS DA SAUDE::ODONTOLOGIA |
title_short |
Influência do laser de diodo na evaporação do solvente de sistemas adesivos em dentina. |
title_full |
Influência do laser de diodo na evaporação do solvente de sistemas adesivos em dentina. |
title_fullStr |
Influência do laser de diodo na evaporação do solvente de sistemas adesivos em dentina. |
title_full_unstemmed |
Influência do laser de diodo na evaporação do solvente de sistemas adesivos em dentina. |
title_sort |
Influência do laser de diodo na evaporação do solvente de sistemas adesivos em dentina. |
author |
Chiattone, Tatiana Dalla Costa |
author_facet |
Chiattone, Tatiana Dalla Costa |
author_role |
author |
dc.contributor.none.fl_str_mv |
Silveira, Bruno Lopes da http://lattes.cnpq.br/8477118220635736 Rocha, Rachel de Oliveira http://lattes.cnpq.br/0239294008628766 Becker, Anne Buss http://lattes.cnpq.br/4794094513719948 Pozzobon, Roselaine Terezinha http://lattes.cnpq.br/0725237903741859 |
dc.contributor.author.fl_str_mv |
Chiattone, Tatiana Dalla Costa |
dc.subject.por.fl_str_mv |
Evaporação Sistema adesivo Laser de diodo Evaporation Adhesive system Diode laser CNPQ::CIENCIAS DA SAUDE::ODONTOLOGIA |
topic |
Evaporação Sistema adesivo Laser de diodo Evaporation Adhesive system Diode laser CNPQ::CIENCIAS DA SAUDE::ODONTOLOGIA |
description |
This study aimed to evaluate, in vitro, the influence of Diode Laser on the evaporation of adhesive systems solvent applied on the dentin. The groups were distributed in relation to the adhesive systems (Adper Single Bond 2, Adper Scotchbond Multi Purpose, Single Bond Universal, Clearfil SE Bond e Optibond All-in-one) and also to the technique for the evaporation of the solvent (air dry stream or Diode Laser). The degree of evaporation (GE) was determined through the measuring of mass loss through the gravimetric method in an analytical digital balance. To do so, a hundred human third molars had cavities class I made of following a pattern with the diamond burs # 4054 (KG Soresen, Barueri, SP, Brasil), under refrigeration, on which 10 μL were dispensed of each adhesive system, then one of the both techniques of solvent evaporation was applied: air dry stream, from a distance of 10 cm for each 5 seconds (control technique) or Diode Laser irradiated in a continuous mode perpendicularly and from a distance of 1 cm, in the power of 3 W in the interval of 30 seconds (experimental technique). To each one of the adhesive systems and to each one of the evaporation techniques ten monitoring repetitions were realized (n=10). Regarding the experimental technique, the measurements were realized from 5 to 5 seconds, up to 30 seconds. The variation between the initial mass (mi) and the final mass (mf) of the samples, respectively, before and after the application methods of evaporation proposed were turned into GE, by using the following equation: (mi-mf/mi)x100. In this way, to each time interval (5, 10, 15, 20, 25 and 30 seconds) it happened a calculated GE outcome. Those values were submitted to variance analysis (ANOVA) of two factors and Tukey s test as well. To the comparison between both of the evaporation techniques in each adhesive system a t-student test (α=5%) was realized. Basing on the obtained values of the GE, verified on the current study, it is possible to conclude that the irradiation with Diode Laser was capable of inducing the solvent evaporation of the tested adhesive systems, being superior to the control technique when used in the time of 30 seconds, excepted to the Optibond-all-in-one adhesive system. |
publishDate |
2015 |
dc.date.none.fl_str_mv |
2015-06-29 2016-02-18 2016-02-18 |
dc.type.status.fl_str_mv |
info:eu-repo/semantics/publishedVersion |
dc.type.driver.fl_str_mv |
info:eu-repo/semantics/masterThesis |
format |
masterThesis |
status_str |
publishedVersion |
dc.identifier.uri.fl_str_mv |
CHIATTONE, Tatiana Dalla Costa. THE INFLUENCE OF DIODE LASER IN EVAPORATION OF ADHESIVE SYSTEMS SOLVENT IN DENTIN. 2015. 43 f. Dissertação (Mestrado em Odontologia) - Universidade Federal de Santa Maria, Santa Maria, 2015. http://repositorio.ufsm.br/handle/1/6161 |
identifier_str_mv |
CHIATTONE, Tatiana Dalla Costa. THE INFLUENCE OF DIODE LASER IN EVAPORATION OF ADHESIVE SYSTEMS SOLVENT IN DENTIN. 2015. 43 f. Dissertação (Mestrado em Odontologia) - Universidade Federal de Santa Maria, Santa Maria, 2015. |
url |
http://repositorio.ufsm.br/handle/1/6161 |
dc.language.iso.fl_str_mv |
por |
language |
por |
dc.rights.driver.fl_str_mv |
info:eu-repo/semantics/openAccess |
eu_rights_str_mv |
openAccess |
dc.format.none.fl_str_mv |
application/pdf application/pdf |
dc.publisher.none.fl_str_mv |
Universidade Federal de Santa Maria BR Odontologia UFSM Programa de Pós-Graduação em Ciências Odontológicas |
publisher.none.fl_str_mv |
Universidade Federal de Santa Maria BR Odontologia UFSM Programa de Pós-Graduação em Ciências Odontológicas |
dc.source.none.fl_str_mv |
reponame:Manancial - Repositório Digital da UFSM instname:Universidade Federal de Santa Maria (UFSM) instacron:UFSM |
instname_str |
Universidade Federal de Santa Maria (UFSM) |
instacron_str |
UFSM |
institution |
UFSM |
reponame_str |
Manancial - Repositório Digital da UFSM |
collection |
Manancial - Repositório Digital da UFSM |
repository.name.fl_str_mv |
Manancial - Repositório Digital da UFSM - Universidade Federal de Santa Maria (UFSM) |
repository.mail.fl_str_mv |
atendimento.sib@ufsm.br||tedebc@gmail.com |
_version_ |
1805922069387411456 |