Contribuições ao estudo da fluidodinâmica em leito de jorro: estudos experimentais e de simulação via CFD
Autor(a) principal: | |
---|---|
Data de Publicação: | 2011 |
Tipo de documento: | Dissertação |
Idioma: | por |
Título da fonte: | Repositório Institucional da UFU |
Texto Completo: | https://repositorio.ufu.br/handle/123456789/15163 |
Resumo: | The spouted bed is characterized by establishing an effective contact between the phases and promoting a cyclical and uniform movement of the particles. This feature is of great industrial importance since most processes require an adequate rate of mass and energy transfer. However, depending on operating and geometric conditions the spouted bed can operate in an unstable regime thus reducing its efficiency. So, a better understanding about its fluid-dynamic behavior is necessary. In order to obtain velocity and porosity profiles in a conical-cylindrical spouted bed, an intrusive fiber optical technique was used. To validate the velocities measured by the probe a non-intrusive method composed by a high-speed video camera was used. As for the calibration of the probe to measure the porosity, it was considered the assumption of linearity between the intensity of the voltage signal captured by the probe and the concentration of solids in a given volume of measurement. The measurements were carried out at different air velocity conditions, diameters of glass spheres and heights in the spouted bed. An investigation about the disturbance caused to the flow by an intrusive technique was performed by recording the height variation and displacement of the fountain. In this work, the Computational Fluid Dynamics (CFD), using the Eulerian Granular Multiphase model was used to determine the porosity and velocity profiles and numerical analysis of the flow disturbance caused by the introduction of the probe under the same experimental conditions. The following drag models were investigated: GIDASPOW et al. (1992), GIDASPOW (1994) and RUC (1994). The GIDASPOW model found in the Fluent® user guide was also used and, as it is written so erroneous in this user guide, small variations when compared to the correct model were obtained. The profiles obtained by simulations using the models GIDASPOW et al. (1992) and GIDASPOW (1994) appeared to underestimate the velocity values in the region of jet while the RUC model slightly overestimates the velocity values in the same region. In the annular region the simulations agree well with the experimental results regardless of the drag model used. It was possible for all conditions examined experimentally to foresee, by means of analysis of the profiles of solids volume fraction simulated, the disturbance caused by the introduction of the probe to the flow. Disturbance was detected with greater intensity in the region of jet and in the transition region between it and the annular region. The disturbance analysis is of great importance while simulating the properties of the flow obtained experimentally by means of an intrusive technique, because in practice the works on simulations present in the literature do not take the disturbance phenomenon into account. |
id |
UFU_1699115f9ddb8cf05ea17effd98e5814 |
---|---|
oai_identifier_str |
oai:repositorio.ufu.br:123456789/15163 |
network_acronym_str |
UFU |
network_name_str |
Repositório Institucional da UFU |
repository_id_str |
|
spelling |
Contribuições ao estudo da fluidodinâmica em leito de jorro: estudos experimentais e de simulação via CFDLeito de jorroSonda de fibra ópticaModelagem multifásicaMétodo intrusivoProcesso de leito de jorroSpouted bedFiber optical probeMultiphase modelingIntrusive methodCNPQ::ENGENHARIAS::ENGENHARIA QUIMICAThe spouted bed is characterized by establishing an effective contact between the phases and promoting a cyclical and uniform movement of the particles. This feature is of great industrial importance since most processes require an adequate rate of mass and energy transfer. However, depending on operating and geometric conditions the spouted bed can operate in an unstable regime thus reducing its efficiency. So, a better understanding about its fluid-dynamic behavior is necessary. In order to obtain velocity and porosity profiles in a conical-cylindrical spouted bed, an intrusive fiber optical technique was used. To validate the velocities measured by the probe a non-intrusive method composed by a high-speed video camera was used. As for the calibration of the probe to measure the porosity, it was considered the assumption of linearity between the intensity of the voltage signal captured by the probe and the concentration of solids in a given volume of measurement. The measurements were carried out at different air velocity conditions, diameters of glass spheres and heights in the spouted bed. An investigation about the disturbance caused to the flow by an intrusive technique was performed by recording the height variation and displacement of the fountain. In this work, the Computational Fluid Dynamics (CFD), using the Eulerian Granular Multiphase model was used to determine the porosity and velocity profiles and numerical analysis of the flow disturbance caused by the introduction of the probe under the same experimental conditions. The following drag models were investigated: GIDASPOW et al. (1992), GIDASPOW (1994) and RUC (1994). The GIDASPOW model found in the Fluent® user guide was also used and, as it is written so erroneous in this user guide, small variations when compared to the correct model were obtained. The profiles obtained by simulations using the models GIDASPOW et al. (1992) and GIDASPOW (1994) appeared to underestimate the velocity values in the region of jet while the RUC model slightly overestimates the velocity values in the same region. In the annular region the simulations agree well with the experimental results regardless of the drag model used. It was possible for all conditions examined experimentally to foresee, by means of analysis of the profiles of solids volume fraction simulated, the disturbance caused by the introduction of the probe to the flow. Disturbance was detected with greater intensity in the region of jet and in the transition region between it and the annular region. The disturbance analysis is of great importance while simulating the properties of the flow obtained experimentally by means of an intrusive technique, because in practice the works on simulations present in the literature do not take the disturbance phenomenon into account.Coordenação de Aperfeiçoamento de Pessoal de Nível SuperiorMestre em Engenharia QuímicaO leito de jorro é caracterizado por estabelecer um movimento cíclico e uniforme das partículas em seu interior promovendo, desta forma, um íntimo contato entre as fases. Esta característica em seu escoamento é de fundamental importância industrial, visto que a maioria dos processos requerem uma adequada taxa de transferência de massa e energia. No entanto, por possuir regiões de escoamento com diferentes caracteristícas e, a depender de suas condições operacionais e geométricas, poder vir a operar em regime de instabilidade, um maior entendimento de seu comportamento fluidodinâmico é necessário. No intuito de se obter perfis de velocidade e porosidade em um leito de jorro cônico-cilíndrico, utilizou-se de uma técnica intrusiva a qual emprega como sonda de medida fibra óptica. Para a validação das medidas de velocidade realizadas por meio da sonda, foi utilizada uma técnica nãointrusiva composta por uma câmera de alta velocidade. Já para a calibração da sonda para a medida de porosidade, considerou-se a suposição de linearidade entre a intensidade do sinal de voltagem captado pela sonda e a concentração de sólidos em um determinado volume de medida. As medidas foram realizadas a diferentes condições de velocidade de ar, diâmetros de esferas de vidro e alturas em relação à entrada do leito. Uma investigação sobre o quanto da perturbação causada ao escoamento na utilização de uma técnica intrusiva foi realizada por meio do registro da variação da altura e do deslocamento da fonte em relação ao eixo central do leito. Empregou-se a técnica de Fluidodinâmica Computacional (CFD), utilizando-se do modelo Euleriano Granular Multifásico, na determinação dos perfis de velocidade e porosidade, e na análise numérica da perturbação causada ao escoamento pela introdução da sonda nas mesmas condições empregadas experimentalmente. Como modelo de arraste, utilizou-se dos modelos de GIDASPOW et al.(1992), GIDASPOW (1994) e RUC (1994). Utilizou-se, também, do modelo de GIDASPOW que se encontra no manual do software Fluent® e, visto que o mesmo se encontra redigido de forma equivocada neste manual, pequenas variações quando comparados ao modelo correto foram obtidas. Os perfis simulados utilizando-se dos modelos de GIDASPOW et al. (1992) e GIDASPOW (1994) subestimaram os valores de velocidade na região de jorro enquanto o modelo RUC superestima os valores de velocidade nesta mesma região, sendo que, na região anular tanto os perfis experimentais quanto os simulados, com diferentes modelos de arraste, se mostraram próximos. Foi possível prever, através da análise dos perfis de fração volumétrica de sólidos simulados, a perturbação causada pela introdução da sonda ao escoamento, verificando uma satisfatória correspondência entre estes e o experimental. Esta perturbação foi detectada com maior intensidade na região de jorro e na região de transição entre esta e a região anular. A análise de perturbação mostrou-se de fundamental importância quando da simulação de perfis de propriedades do escoamento obtidos experimentalmente por uma técnica intrusiva, pois, na prática os trabalhos sobre simulações encontrados na literatura não levam o fenômeno da perturbação em consideração.Universidade Federal de UberlândiaBRPrograma de Pós-graduação em Engenharia QuímicaEngenhariasUFUBarrozo, Marcos Antonio de Souzahttp://buscatextual.cnpq.br/buscatextual/visualizacv.do?id=K4787095J7Duarte, Claudio Robertohttp://buscatextual.cnpq.br/buscatextual/visualizacv.do?id=K4708473P5Ataide, Carlos Henriquehttp://buscatextual.cnpq.br/buscatextual/visualizacv.do?id=K4787952H6Vieira, Luiz Gustavo Martinshttp://buscatextual.cnpq.br/buscatextual/visualizacv.do?id=K4767723D6Béttega, Rodrigohttp://buscatextual.cnpq.br/buscatextual/visualizacv.do?id=K4777874P8Pereira, Fábio de Assis Resselhttp://buscatextual.cnpq.br/buscatextual/visualizacv.do?id=K4768331U0Santos, Dyrney Araújo dos2016-06-22T18:41:42Z2011-10-112016-06-22T18:41:42Z2011-07-29info:eu-repo/semantics/publishedVersioninfo:eu-repo/semantics/masterThesisapplication/pdfapplication/pdfSANTOS, Dyrney Araújo dos. Contribuições ao estudo da fluidodinâmica em leito de jorro: estudos experimentais e de simulação via CFD. 2011. 125 f. Dissertação (Mestrado em Engenharias) - Universidade Federal de Uberlândia, Uberlândia, 2011.https://repositorio.ufu.br/handle/123456789/15163porinfo:eu-repo/semantics/openAccessreponame:Repositório Institucional da UFUinstname:Universidade Federal de Uberlândia (UFU)instacron:UFU2016-06-23T07:01:42Zoai:repositorio.ufu.br:123456789/15163Repositório InstitucionalONGhttp://repositorio.ufu.br/oai/requestdiinf@dirbi.ufu.bropendoar:2016-06-23T07:01:42Repositório Institucional da UFU - Universidade Federal de Uberlândia (UFU)false |
dc.title.none.fl_str_mv |
Contribuições ao estudo da fluidodinâmica em leito de jorro: estudos experimentais e de simulação via CFD |
title |
Contribuições ao estudo da fluidodinâmica em leito de jorro: estudos experimentais e de simulação via CFD |
spellingShingle |
Contribuições ao estudo da fluidodinâmica em leito de jorro: estudos experimentais e de simulação via CFD Santos, Dyrney Araújo dos Leito de jorro Sonda de fibra óptica Modelagem multifásica Método intrusivo Processo de leito de jorro Spouted bed Fiber optical probe Multiphase modeling Intrusive method CNPQ::ENGENHARIAS::ENGENHARIA QUIMICA |
title_short |
Contribuições ao estudo da fluidodinâmica em leito de jorro: estudos experimentais e de simulação via CFD |
title_full |
Contribuições ao estudo da fluidodinâmica em leito de jorro: estudos experimentais e de simulação via CFD |
title_fullStr |
Contribuições ao estudo da fluidodinâmica em leito de jorro: estudos experimentais e de simulação via CFD |
title_full_unstemmed |
Contribuições ao estudo da fluidodinâmica em leito de jorro: estudos experimentais e de simulação via CFD |
title_sort |
Contribuições ao estudo da fluidodinâmica em leito de jorro: estudos experimentais e de simulação via CFD |
author |
Santos, Dyrney Araújo dos |
author_facet |
Santos, Dyrney Araújo dos |
author_role |
author |
dc.contributor.none.fl_str_mv |
Barrozo, Marcos Antonio de Souza http://buscatextual.cnpq.br/buscatextual/visualizacv.do?id=K4787095J7 Duarte, Claudio Roberto http://buscatextual.cnpq.br/buscatextual/visualizacv.do?id=K4708473P5 Ataide, Carlos Henrique http://buscatextual.cnpq.br/buscatextual/visualizacv.do?id=K4787952H6 Vieira, Luiz Gustavo Martins http://buscatextual.cnpq.br/buscatextual/visualizacv.do?id=K4767723D6 Béttega, Rodrigo http://buscatextual.cnpq.br/buscatextual/visualizacv.do?id=K4777874P8 Pereira, Fábio de Assis Ressel http://buscatextual.cnpq.br/buscatextual/visualizacv.do?id=K4768331U0 |
dc.contributor.author.fl_str_mv |
Santos, Dyrney Araújo dos |
dc.subject.por.fl_str_mv |
Leito de jorro Sonda de fibra óptica Modelagem multifásica Método intrusivo Processo de leito de jorro Spouted bed Fiber optical probe Multiphase modeling Intrusive method CNPQ::ENGENHARIAS::ENGENHARIA QUIMICA |
topic |
Leito de jorro Sonda de fibra óptica Modelagem multifásica Método intrusivo Processo de leito de jorro Spouted bed Fiber optical probe Multiphase modeling Intrusive method CNPQ::ENGENHARIAS::ENGENHARIA QUIMICA |
description |
The spouted bed is characterized by establishing an effective contact between the phases and promoting a cyclical and uniform movement of the particles. This feature is of great industrial importance since most processes require an adequate rate of mass and energy transfer. However, depending on operating and geometric conditions the spouted bed can operate in an unstable regime thus reducing its efficiency. So, a better understanding about its fluid-dynamic behavior is necessary. In order to obtain velocity and porosity profiles in a conical-cylindrical spouted bed, an intrusive fiber optical technique was used. To validate the velocities measured by the probe a non-intrusive method composed by a high-speed video camera was used. As for the calibration of the probe to measure the porosity, it was considered the assumption of linearity between the intensity of the voltage signal captured by the probe and the concentration of solids in a given volume of measurement. The measurements were carried out at different air velocity conditions, diameters of glass spheres and heights in the spouted bed. An investigation about the disturbance caused to the flow by an intrusive technique was performed by recording the height variation and displacement of the fountain. In this work, the Computational Fluid Dynamics (CFD), using the Eulerian Granular Multiphase model was used to determine the porosity and velocity profiles and numerical analysis of the flow disturbance caused by the introduction of the probe under the same experimental conditions. The following drag models were investigated: GIDASPOW et al. (1992), GIDASPOW (1994) and RUC (1994). The GIDASPOW model found in the Fluent® user guide was also used and, as it is written so erroneous in this user guide, small variations when compared to the correct model were obtained. The profiles obtained by simulations using the models GIDASPOW et al. (1992) and GIDASPOW (1994) appeared to underestimate the velocity values in the region of jet while the RUC model slightly overestimates the velocity values in the same region. In the annular region the simulations agree well with the experimental results regardless of the drag model used. It was possible for all conditions examined experimentally to foresee, by means of analysis of the profiles of solids volume fraction simulated, the disturbance caused by the introduction of the probe to the flow. Disturbance was detected with greater intensity in the region of jet and in the transition region between it and the annular region. The disturbance analysis is of great importance while simulating the properties of the flow obtained experimentally by means of an intrusive technique, because in practice the works on simulations present in the literature do not take the disturbance phenomenon into account. |
publishDate |
2011 |
dc.date.none.fl_str_mv |
2011-10-11 2011-07-29 2016-06-22T18:41:42Z 2016-06-22T18:41:42Z |
dc.type.status.fl_str_mv |
info:eu-repo/semantics/publishedVersion |
dc.type.driver.fl_str_mv |
info:eu-repo/semantics/masterThesis |
format |
masterThesis |
status_str |
publishedVersion |
dc.identifier.uri.fl_str_mv |
SANTOS, Dyrney Araújo dos. Contribuições ao estudo da fluidodinâmica em leito de jorro: estudos experimentais e de simulação via CFD. 2011. 125 f. Dissertação (Mestrado em Engenharias) - Universidade Federal de Uberlândia, Uberlândia, 2011. https://repositorio.ufu.br/handle/123456789/15163 |
identifier_str_mv |
SANTOS, Dyrney Araújo dos. Contribuições ao estudo da fluidodinâmica em leito de jorro: estudos experimentais e de simulação via CFD. 2011. 125 f. Dissertação (Mestrado em Engenharias) - Universidade Federal de Uberlândia, Uberlândia, 2011. |
url |
https://repositorio.ufu.br/handle/123456789/15163 |
dc.language.iso.fl_str_mv |
por |
language |
por |
dc.rights.driver.fl_str_mv |
info:eu-repo/semantics/openAccess |
eu_rights_str_mv |
openAccess |
dc.format.none.fl_str_mv |
application/pdf application/pdf |
dc.publisher.none.fl_str_mv |
Universidade Federal de Uberlândia BR Programa de Pós-graduação em Engenharia Química Engenharias UFU |
publisher.none.fl_str_mv |
Universidade Federal de Uberlândia BR Programa de Pós-graduação em Engenharia Química Engenharias UFU |
dc.source.none.fl_str_mv |
reponame:Repositório Institucional da UFU instname:Universidade Federal de Uberlândia (UFU) instacron:UFU |
instname_str |
Universidade Federal de Uberlândia (UFU) |
instacron_str |
UFU |
institution |
UFU |
reponame_str |
Repositório Institucional da UFU |
collection |
Repositório Institucional da UFU |
repository.name.fl_str_mv |
Repositório Institucional da UFU - Universidade Federal de Uberlândia (UFU) |
repository.mail.fl_str_mv |
diinf@dirbi.ufu.br |
_version_ |
1805569706293198848 |