Desidratação parcial de tomate cereja em secador de bandejas vibradas com reciclo
Autor(a) principal: | |
---|---|
Data de Publicação: | 2011 |
Tipo de documento: | Dissertação |
Idioma: | por |
Título da fonte: | Repositório Institucional da UFU |
Texto Completo: | https://repositorio.ufu.br/handle/123456789/15158 |
Resumo: | In this essay, it has been analyzed the partial dehydration of oval cherry tomato Lycopersicum sp. Mill, by using a vibrated tray dryer with recycle until the tomatoes reached 15% of its initial water content what represents 70,19% of humidity in wet basis or 2,35 kg of water/kg of dry mass in dry basis. The dryer used consists basically of a vertical dryer tunnel with four perforated trays by whose perforations tomatoes and air flow where drained in a crossed way, being the latter injected at the bottom of a pipe connected to a blower, allowing the adjustment of output and also to go through a series of four resistors that sets the temperature. All trays are connected to a vibration system that helps the tomatoes flow, which are recirculated with the aid of a conveyor belt. CCD was used to verify the influence of significant variables of the process: air flow, temperature and tomatoes mass. The analyzed response was the amount of in natura tomatoes processed in a day. The optimum operating condition was experimentally reproduced, validating the results obtained in the CCD, where there was obtained 18, 729 kg of tomatoes processed per day, with an optimum temperature of 67.6 ° C, airflow rate 6 kg / min and amount of processed tomatoes of 4.025 kg. In the optimum condition of the dryer it has been studied the drying curve and drying kinetics. The drying process started with the dryer working in batch without tomatoes recicle, until achieve the moisture content of 85% approximately, followed by the addition of porcelain spheres with a diameter of 0.0235 m, that forced the tomatoes particles flow and the process began to occur with recirculation. In the drying knetics, three periods were identified: two periods that the dried tomatoes in steady state rates, interspersed with a variable rate period. For the drying rates constants, quantified values of the correlation coefficient above 0.99, linear fitting a straight line with the experimental points. Comparing the behavior of the fixed bed with the vibrated bed, it was observed that the application of vibration acted in decreasing by 30% the drying time. The results indicated that the simultaneous influence of vibration and porcelain balls intensify the drying process, resulting in a peculiar air drying. |
id |
UFU_7329ad6307991361f34a3fc56ce81964 |
---|---|
oai_identifier_str |
oai:repositorio.ufu.br:123456789/15158 |
network_acronym_str |
UFU |
network_name_str |
Repositório Institucional da UFU |
repository_id_str |
|
spelling |
Desidratação parcial de tomate cereja em secador de bandejas vibradas com recicloTomate cerejaVibraçãoCinética de secagemPlanejamento composto centralSecagemTomate - SecagemDryingCherry tomatoesVibrationDrying kineticsCentral composite designCNPQ::ENGENHARIAS::ENGENHARIA QUIMICAIn this essay, it has been analyzed the partial dehydration of oval cherry tomato Lycopersicum sp. Mill, by using a vibrated tray dryer with recycle until the tomatoes reached 15% of its initial water content what represents 70,19% of humidity in wet basis or 2,35 kg of water/kg of dry mass in dry basis. The dryer used consists basically of a vertical dryer tunnel with four perforated trays by whose perforations tomatoes and air flow where drained in a crossed way, being the latter injected at the bottom of a pipe connected to a blower, allowing the adjustment of output and also to go through a series of four resistors that sets the temperature. All trays are connected to a vibration system that helps the tomatoes flow, which are recirculated with the aid of a conveyor belt. CCD was used to verify the influence of significant variables of the process: air flow, temperature and tomatoes mass. The analyzed response was the amount of in natura tomatoes processed in a day. The optimum operating condition was experimentally reproduced, validating the results obtained in the CCD, where there was obtained 18, 729 kg of tomatoes processed per day, with an optimum temperature of 67.6 ° C, airflow rate 6 kg / min and amount of processed tomatoes of 4.025 kg. In the optimum condition of the dryer it has been studied the drying curve and drying kinetics. The drying process started with the dryer working in batch without tomatoes recicle, until achieve the moisture content of 85% approximately, followed by the addition of porcelain spheres with a diameter of 0.0235 m, that forced the tomatoes particles flow and the process began to occur with recirculation. In the drying knetics, three periods were identified: two periods that the dried tomatoes in steady state rates, interspersed with a variable rate period. For the drying rates constants, quantified values of the correlation coefficient above 0.99, linear fitting a straight line with the experimental points. Comparing the behavior of the fixed bed with the vibrated bed, it was observed that the application of vibration acted in decreasing by 30% the drying time. The results indicated that the simultaneous influence of vibration and porcelain balls intensify the drying process, resulting in a peculiar air drying.Fundação de Amparo a Pesquisa do Estado de Minas GeraisMestre em Engenharia QuímicaPara o presente estudo, foi analisada a desidratação parcial do tomate cereja ovalado, Lycopersicum sp. Mill., e utilizou-se de um secador de bandejas vibradas com reciclo até que o tomate atingisse 15% do conteúdo de água inicial, o que representa 70,19 % de umidade em base úmida ou 2,35 kg de água/kg de massa seca em base seca. O secador estudado consiste basicamente de um túnel vertical de secagem com quatro bandejas perfuradas por onde escoam de maneira cruzada o tomate e o ar aquecido. Todas as bandejas estão conectadas a um sistema de vibração que auxilia no escoamento dos tomates, para que durante o processamento os frutos sejam conduzidos à uma esteira que auxilia na recirculação dos frutos. Um PCC foi desenvolvido para quantificar a influência das variáveis significativas do processo: vazão de ar, temperatura e massa de tomate alimentada. A resposta analisada foi a quantidade de tomate in natura processada em um dia. A condição ótima de operação foi reproduzida experimentalmente, validando os resultados obtidos no PCC, em que obteve-se 18,729 kg de tomate processados/dia, com a temperatura ótima de 67,6°C, vazão de ar 6 kg/min e quantidade de tomate alimentado de 4,025 kg. Na condição ótima do secador estudou-se a curva de secagem e a cinética de secagem. O processo de secagem iniciou-se com o secador operando em batelada sem recirculação dos frutos, até que se atingiu o teor de umidade de aproximadamente 85%, seguindo-se a adição de esferas de porcelana com 0,0235 m de diâmetro, as quais forçaram o escoamento das partículas de tomate e o processo passou a ocorrer com recirculação. Na cinética de secagem, três períodos foram identificados: dois períodos em que os tomates secaram em taxas constantes, intercalados por um período com taxa variável. Para as taxas de secagem constantes, quantificaram-se os valores do coeficiente de correlação superiores a 0,99, ao ajustar uma reta aos pontos experimentais. Comparando-se o comportamento do leito fixo com o vibrado, observou-se que a aplicação da vibração atuou diminuindo em 30% o tempo de secagem. Os resultados indicaram que a influência simultânea da vibração e das esferas de porcelana intensificam o processo de secagem, resultando em uma cinética de secagem peculiar.Universidade Federal de UberlândiaBRPrograma de Pós-graduação em Engenharia QuímicaEngenhariasUFUFinzer, José Roberto Delaliberahttp://buscatextual.cnpq.br/buscatextual/visualizacv.do?id=K4783606Y8Ribeiro, Eloizio Juliohttp://buscatextual.cnpq.br/buscatextual/visualizacv.do?id=K4721952Y1Lopes, Luís Cláudio Oliveirahttp://buscatextual.cnpq.br/buscatextual/visualizacv.do?id=K4797749Y8Miguel, Daniela Pereshttp://buscatextual.cnpq.br/buscatextual/visualizacv.do?id=K4770973U9Lourenço, Giovani Aud2016-06-22T18:41:41Z2011-05-172016-06-22T18:41:41Z2011-02-25info:eu-repo/semantics/publishedVersioninfo:eu-repo/semantics/masterThesisapplication/pdfapplication/pdfLOURENÇO, Giovani Aud. Desidratação parcial de tomate cereja em secador de bandejas vibradas com reciclo. 2011. 111 f. Dissertação (Mestrado em Engenharias) - Universidade Federal de Uberlândia, Uberlândia, 2011.https://repositorio.ufu.br/handle/123456789/15158porinfo:eu-repo/semantics/openAccessreponame:Repositório Institucional da UFUinstname:Universidade Federal de Uberlândia (UFU)instacron:UFU2021-09-17T13:42:52Zoai:repositorio.ufu.br:123456789/15158Repositório InstitucionalONGhttp://repositorio.ufu.br/oai/requestdiinf@dirbi.ufu.bropendoar:2021-09-17T13:42:52Repositório Institucional da UFU - Universidade Federal de Uberlândia (UFU)false |
dc.title.none.fl_str_mv |
Desidratação parcial de tomate cereja em secador de bandejas vibradas com reciclo |
title |
Desidratação parcial de tomate cereja em secador de bandejas vibradas com reciclo |
spellingShingle |
Desidratação parcial de tomate cereja em secador de bandejas vibradas com reciclo Lourenço, Giovani Aud Tomate cereja Vibração Cinética de secagem Planejamento composto central Secagem Tomate - Secagem Drying Cherry tomatoes Vibration Drying kinetics Central composite design CNPQ::ENGENHARIAS::ENGENHARIA QUIMICA |
title_short |
Desidratação parcial de tomate cereja em secador de bandejas vibradas com reciclo |
title_full |
Desidratação parcial de tomate cereja em secador de bandejas vibradas com reciclo |
title_fullStr |
Desidratação parcial de tomate cereja em secador de bandejas vibradas com reciclo |
title_full_unstemmed |
Desidratação parcial de tomate cereja em secador de bandejas vibradas com reciclo |
title_sort |
Desidratação parcial de tomate cereja em secador de bandejas vibradas com reciclo |
author |
Lourenço, Giovani Aud |
author_facet |
Lourenço, Giovani Aud |
author_role |
author |
dc.contributor.none.fl_str_mv |
Finzer, José Roberto Delalibera http://buscatextual.cnpq.br/buscatextual/visualizacv.do?id=K4783606Y8 Ribeiro, Eloizio Julio http://buscatextual.cnpq.br/buscatextual/visualizacv.do?id=K4721952Y1 Lopes, Luís Cláudio Oliveira http://buscatextual.cnpq.br/buscatextual/visualizacv.do?id=K4797749Y8 Miguel, Daniela Peres http://buscatextual.cnpq.br/buscatextual/visualizacv.do?id=K4770973U9 |
dc.contributor.author.fl_str_mv |
Lourenço, Giovani Aud |
dc.subject.por.fl_str_mv |
Tomate cereja Vibração Cinética de secagem Planejamento composto central Secagem Tomate - Secagem Drying Cherry tomatoes Vibration Drying kinetics Central composite design CNPQ::ENGENHARIAS::ENGENHARIA QUIMICA |
topic |
Tomate cereja Vibração Cinética de secagem Planejamento composto central Secagem Tomate - Secagem Drying Cherry tomatoes Vibration Drying kinetics Central composite design CNPQ::ENGENHARIAS::ENGENHARIA QUIMICA |
description |
In this essay, it has been analyzed the partial dehydration of oval cherry tomato Lycopersicum sp. Mill, by using a vibrated tray dryer with recycle until the tomatoes reached 15% of its initial water content what represents 70,19% of humidity in wet basis or 2,35 kg of water/kg of dry mass in dry basis. The dryer used consists basically of a vertical dryer tunnel with four perforated trays by whose perforations tomatoes and air flow where drained in a crossed way, being the latter injected at the bottom of a pipe connected to a blower, allowing the adjustment of output and also to go through a series of four resistors that sets the temperature. All trays are connected to a vibration system that helps the tomatoes flow, which are recirculated with the aid of a conveyor belt. CCD was used to verify the influence of significant variables of the process: air flow, temperature and tomatoes mass. The analyzed response was the amount of in natura tomatoes processed in a day. The optimum operating condition was experimentally reproduced, validating the results obtained in the CCD, where there was obtained 18, 729 kg of tomatoes processed per day, with an optimum temperature of 67.6 ° C, airflow rate 6 kg / min and amount of processed tomatoes of 4.025 kg. In the optimum condition of the dryer it has been studied the drying curve and drying kinetics. The drying process started with the dryer working in batch without tomatoes recicle, until achieve the moisture content of 85% approximately, followed by the addition of porcelain spheres with a diameter of 0.0235 m, that forced the tomatoes particles flow and the process began to occur with recirculation. In the drying knetics, three periods were identified: two periods that the dried tomatoes in steady state rates, interspersed with a variable rate period. For the drying rates constants, quantified values of the correlation coefficient above 0.99, linear fitting a straight line with the experimental points. Comparing the behavior of the fixed bed with the vibrated bed, it was observed that the application of vibration acted in decreasing by 30% the drying time. The results indicated that the simultaneous influence of vibration and porcelain balls intensify the drying process, resulting in a peculiar air drying. |
publishDate |
2011 |
dc.date.none.fl_str_mv |
2011-05-17 2011-02-25 2016-06-22T18:41:41Z 2016-06-22T18:41:41Z |
dc.type.status.fl_str_mv |
info:eu-repo/semantics/publishedVersion |
dc.type.driver.fl_str_mv |
info:eu-repo/semantics/masterThesis |
format |
masterThesis |
status_str |
publishedVersion |
dc.identifier.uri.fl_str_mv |
LOURENÇO, Giovani Aud. Desidratação parcial de tomate cereja em secador de bandejas vibradas com reciclo. 2011. 111 f. Dissertação (Mestrado em Engenharias) - Universidade Federal de Uberlândia, Uberlândia, 2011. https://repositorio.ufu.br/handle/123456789/15158 |
identifier_str_mv |
LOURENÇO, Giovani Aud. Desidratação parcial de tomate cereja em secador de bandejas vibradas com reciclo. 2011. 111 f. Dissertação (Mestrado em Engenharias) - Universidade Federal de Uberlândia, Uberlândia, 2011. |
url |
https://repositorio.ufu.br/handle/123456789/15158 |
dc.language.iso.fl_str_mv |
por |
language |
por |
dc.rights.driver.fl_str_mv |
info:eu-repo/semantics/openAccess |
eu_rights_str_mv |
openAccess |
dc.format.none.fl_str_mv |
application/pdf application/pdf |
dc.publisher.none.fl_str_mv |
Universidade Federal de Uberlândia BR Programa de Pós-graduação em Engenharia Química Engenharias UFU |
publisher.none.fl_str_mv |
Universidade Federal de Uberlândia BR Programa de Pós-graduação em Engenharia Química Engenharias UFU |
dc.source.none.fl_str_mv |
reponame:Repositório Institucional da UFU instname:Universidade Federal de Uberlândia (UFU) instacron:UFU |
instname_str |
Universidade Federal de Uberlândia (UFU) |
instacron_str |
UFU |
institution |
UFU |
reponame_str |
Repositório Institucional da UFU |
collection |
Repositório Institucional da UFU |
repository.name.fl_str_mv |
Repositório Institucional da UFU - Universidade Federal de Uberlândia (UFU) |
repository.mail.fl_str_mv |
diinf@dirbi.ufu.br |
_version_ |
1813711530701619200 |