Influência do ângulo de posição secundário da ferramenta, raio de ponta e lubrificação na usinagem em presença de aresta postiça de corte
Autor(a) principal: | |
---|---|
Data de Publicação: | 2000 |
Tipo de documento: | Dissertação |
Idioma: | por |
Título da fonte: | Repositório Institucional da UFU |
Texto Completo: | https://repositorio.ufu.br/handle/123456789/30007 http://doi.org/10.14393/ufu.di.2000.52 |
Resumo: | This work investigates the influence of tool end cutting edge angle and tool nose radius on surface finish of AISI 1045 steel machined under built-up edge conditions. Surface roughness was evaluated measuring the Ra parameter and analysis of the geometry of the machined surface was carried out in the scanning electron microscope. To assist this work, the three main machining forces components were measured during cutting using a Kistler piezoelectric dynamometer. High speed Steel tools with the same substrate composition and geometry but varying end cutting edge angle, between 1° to 45°, were used. To study the effect of tool nose radius it was used three coated cemented Carbide tools from class ISO P25 with same geometry but different tool nose radius (0,4mm. 0,8mm and 1,2mm). Ra measurement and scanning electron microscope analysis showed that improved surface finish can be achieved by reducing the end cutting edge angle. The effect of a neat oil lubricant with EP additives applied at very low rate (12 ml/min) was also studied. The lubricant improved surface finish and its effect depends on the end cutting edge angle. The effects of this angle and the very low volume of lubricant suggest a mechanism of lubrication where the oil does not need to penetrate into the chip tool interface avoiding built up edge formation to improve surface finish. The lubricant acts on the machined surface close to the tool nose radius. |
id |
UFU_944e86543a056c141a5690f1d8005850 |
---|---|
oai_identifier_str |
oai:repositorio.ufu.br:123456789/30007 |
network_acronym_str |
UFU |
network_name_str |
Repositório Institucional da UFU |
repository_id_str |
|
spelling |
Influência do ângulo de posição secundário da ferramenta, raio de ponta e lubrificação na usinagem em presença de aresta postiça de corteInfluence of the secondary position angle of the tool, nose radius and lubrication when machining in the presence of a cutting edgeAcabamento superficialÂngulo de posição secundárioRaio de pontaAresta postiça de corteFluido de corteMachiningLubricationBuilt up edgeSurface finishCNPQ::ENGENHARIASUsinagemThis work investigates the influence of tool end cutting edge angle and tool nose radius on surface finish of AISI 1045 steel machined under built-up edge conditions. Surface roughness was evaluated measuring the Ra parameter and analysis of the geometry of the machined surface was carried out in the scanning electron microscope. To assist this work, the three main machining forces components were measured during cutting using a Kistler piezoelectric dynamometer. High speed Steel tools with the same substrate composition and geometry but varying end cutting edge angle, between 1° to 45°, were used. To study the effect of tool nose radius it was used three coated cemented Carbide tools from class ISO P25 with same geometry but different tool nose radius (0,4mm. 0,8mm and 1,2mm). Ra measurement and scanning electron microscope analysis showed that improved surface finish can be achieved by reducing the end cutting edge angle. The effect of a neat oil lubricant with EP additives applied at very low rate (12 ml/min) was also studied. The lubricant improved surface finish and its effect depends on the end cutting edge angle. The effects of this angle and the very low volume of lubricant suggest a mechanism of lubrication where the oil does not need to penetrate into the chip tool interface avoiding built up edge formation to improve surface finish. The lubricant acts on the machined surface close to the tool nose radius.Dissertação (Mestrado)Este trabalho analisa a influência do ângulo de posição secundário (x’r) e do raio de ponta (rs) da ferramenta de corte sobre o acabamento superficial de peças de aço ABNT 1045, torneadas em condições de usinagem propícias à formação de aresta postiça de corte (APC). Neste trabalho também foi analisado o efeito da aplicação de um pequeno volume de fluido de corte por gotejamento (vazão - 12ml/min), sobre o acabamento superficial. O estudo da influência destas variáveis sobre o acabamento superficial foi feito através da medida do parâmetro Ra da superfície usinada e da análise de amostras destas superfícies em um microscópio eletrônico de varredura (MEV). Para auxiliar neste estudo, foram medidas as forças de corte (Fc), de avanço (Ff) e passiva (Fp), utilizando-se um dinamômetroKistler 9265B. Para verificar a influência do ângulo %’r sobre o acabamento da superfície usinada, foram utilizadas ferramentas de aço-rápido cujas cunhas cortantes possuíam a mesma geometria (a0=5°,y0=50, Às=0°, Xr= 45°), diferenciando-se apenas nos valores de x’r que variou de 1° à 45° . Na verificação da influência do re, foram utilizadas três patilhas de metal duro da classe P25 revestidas com TIC e TIN (a0=110,y0=60, Xs=0°, Xr=60°, x ’r=60°) com re igual a 0,4mm, 0,8mm e 1,2mm. Os resultados mostraram que o uso de fluido de corte, gotejado sobre a superfície da peça próximo a ponta da ferramenta, tende a melhorar o acabamento da peça em termos de Ra. Todavia esta melhora se dá de maneira muito mais acentuada para pequenos/r ( 1° à 5°) e para as ferramentas com raios de ponta. A forma de aplicação do fluido e o pequeno volume utilizado sugerem um mecanismo de lubrificação onde o fluido de corte melhora o acabamento sem, contudo, penetrar na interface cavaco-ferramenta e eliminar a APC. As análises feitas no MEV permitiram a identificação de partículas de APC, comprimidas entre a superfície secundária de folga da ferramenta e a superfície da peça em usinagem secundária. Neste sentido o fluido de corte em pequeno volume lubrifica a superfície recém usinada da peça evitando ou diminuindo a aderência destas partículas sobre a superfície e, conseqüentemente, melhorando o seu acabamento.Universidade Federal de UberlândiaBrasilPrograma de Pós-graduação em Engenharia MecânicaSilva, Marcio Bacci daConsalter, Luiz AirtonMachado, Álisson RochaReis, Alexandre Martins2020-10-05T18:08:36Z2020-10-05T18:08:36Z2000info:eu-repo/semantics/publishedVersioninfo:eu-repo/semantics/masterThesisapplication/pdfREIS, Alexandre Martins. Influência do ângulo de posição secundário da ferramenta, raio de ponta e lubrificação na usinagem em presença de aresta postiça de corte. 2000. 90 f. Dissertação (Mestrado em Engenharia Mecânica) - Universidade Federal de Uberlândia, Uberlândia, 2020. DOI http://doi.org/10.14393/ufu.di.2000.52https://repositorio.ufu.br/handle/123456789/30007http://doi.org/10.14393/ufu.di.2000.52porhttp://creativecommons.org/licenses/by-nc-nd/3.0/us/info:eu-repo/semantics/openAccessreponame:Repositório Institucional da UFUinstname:Universidade Federal de Uberlândia (UFU)instacron:UFU2021-10-19T19:37:13Zoai:repositorio.ufu.br:123456789/30007Repositório InstitucionalONGhttp://repositorio.ufu.br/oai/requestdiinf@dirbi.ufu.bropendoar:2021-10-19T19:37:13Repositório Institucional da UFU - Universidade Federal de Uberlândia (UFU)false |
dc.title.none.fl_str_mv |
Influência do ângulo de posição secundário da ferramenta, raio de ponta e lubrificação na usinagem em presença de aresta postiça de corte Influence of the secondary position angle of the tool, nose radius and lubrication when machining in the presence of a cutting edge |
title |
Influência do ângulo de posição secundário da ferramenta, raio de ponta e lubrificação na usinagem em presença de aresta postiça de corte |
spellingShingle |
Influência do ângulo de posição secundário da ferramenta, raio de ponta e lubrificação na usinagem em presença de aresta postiça de corte Reis, Alexandre Martins Acabamento superficial Ângulo de posição secundário Raio de ponta Aresta postiça de corte Fluido de corte Machining Lubrication Built up edge Surface finish CNPQ::ENGENHARIAS Usinagem |
title_short |
Influência do ângulo de posição secundário da ferramenta, raio de ponta e lubrificação na usinagem em presença de aresta postiça de corte |
title_full |
Influência do ângulo de posição secundário da ferramenta, raio de ponta e lubrificação na usinagem em presença de aresta postiça de corte |
title_fullStr |
Influência do ângulo de posição secundário da ferramenta, raio de ponta e lubrificação na usinagem em presença de aresta postiça de corte |
title_full_unstemmed |
Influência do ângulo de posição secundário da ferramenta, raio de ponta e lubrificação na usinagem em presença de aresta postiça de corte |
title_sort |
Influência do ângulo de posição secundário da ferramenta, raio de ponta e lubrificação na usinagem em presença de aresta postiça de corte |
author |
Reis, Alexandre Martins |
author_facet |
Reis, Alexandre Martins |
author_role |
author |
dc.contributor.none.fl_str_mv |
Silva, Marcio Bacci da Consalter, Luiz Airton Machado, Álisson Rocha |
dc.contributor.author.fl_str_mv |
Reis, Alexandre Martins |
dc.subject.por.fl_str_mv |
Acabamento superficial Ângulo de posição secundário Raio de ponta Aresta postiça de corte Fluido de corte Machining Lubrication Built up edge Surface finish CNPQ::ENGENHARIAS Usinagem |
topic |
Acabamento superficial Ângulo de posição secundário Raio de ponta Aresta postiça de corte Fluido de corte Machining Lubrication Built up edge Surface finish CNPQ::ENGENHARIAS Usinagem |
description |
This work investigates the influence of tool end cutting edge angle and tool nose radius on surface finish of AISI 1045 steel machined under built-up edge conditions. Surface roughness was evaluated measuring the Ra parameter and analysis of the geometry of the machined surface was carried out in the scanning electron microscope. To assist this work, the three main machining forces components were measured during cutting using a Kistler piezoelectric dynamometer. High speed Steel tools with the same substrate composition and geometry but varying end cutting edge angle, between 1° to 45°, were used. To study the effect of tool nose radius it was used three coated cemented Carbide tools from class ISO P25 with same geometry but different tool nose radius (0,4mm. 0,8mm and 1,2mm). Ra measurement and scanning electron microscope analysis showed that improved surface finish can be achieved by reducing the end cutting edge angle. The effect of a neat oil lubricant with EP additives applied at very low rate (12 ml/min) was also studied. The lubricant improved surface finish and its effect depends on the end cutting edge angle. The effects of this angle and the very low volume of lubricant suggest a mechanism of lubrication where the oil does not need to penetrate into the chip tool interface avoiding built up edge formation to improve surface finish. The lubricant acts on the machined surface close to the tool nose radius. |
publishDate |
2000 |
dc.date.none.fl_str_mv |
2000 2020-10-05T18:08:36Z 2020-10-05T18:08:36Z |
dc.type.status.fl_str_mv |
info:eu-repo/semantics/publishedVersion |
dc.type.driver.fl_str_mv |
info:eu-repo/semantics/masterThesis |
format |
masterThesis |
status_str |
publishedVersion |
dc.identifier.uri.fl_str_mv |
REIS, Alexandre Martins. Influência do ângulo de posição secundário da ferramenta, raio de ponta e lubrificação na usinagem em presença de aresta postiça de corte. 2000. 90 f. Dissertação (Mestrado em Engenharia Mecânica) - Universidade Federal de Uberlândia, Uberlândia, 2020. DOI http://doi.org/10.14393/ufu.di.2000.52 https://repositorio.ufu.br/handle/123456789/30007 http://doi.org/10.14393/ufu.di.2000.52 |
identifier_str_mv |
REIS, Alexandre Martins. Influência do ângulo de posição secundário da ferramenta, raio de ponta e lubrificação na usinagem em presença de aresta postiça de corte. 2000. 90 f. Dissertação (Mestrado em Engenharia Mecânica) - Universidade Federal de Uberlândia, Uberlândia, 2020. DOI http://doi.org/10.14393/ufu.di.2000.52 |
url |
https://repositorio.ufu.br/handle/123456789/30007 http://doi.org/10.14393/ufu.di.2000.52 |
dc.language.iso.fl_str_mv |
por |
language |
por |
dc.rights.driver.fl_str_mv |
http://creativecommons.org/licenses/by-nc-nd/3.0/us/ info:eu-repo/semantics/openAccess |
rights_invalid_str_mv |
http://creativecommons.org/licenses/by-nc-nd/3.0/us/ |
eu_rights_str_mv |
openAccess |
dc.format.none.fl_str_mv |
application/pdf |
dc.publisher.none.fl_str_mv |
Universidade Federal de Uberlândia Brasil Programa de Pós-graduação em Engenharia Mecânica |
publisher.none.fl_str_mv |
Universidade Federal de Uberlândia Brasil Programa de Pós-graduação em Engenharia Mecânica |
dc.source.none.fl_str_mv |
reponame:Repositório Institucional da UFU instname:Universidade Federal de Uberlândia (UFU) instacron:UFU |
instname_str |
Universidade Federal de Uberlândia (UFU) |
instacron_str |
UFU |
institution |
UFU |
reponame_str |
Repositório Institucional da UFU |
collection |
Repositório Institucional da UFU |
repository.name.fl_str_mv |
Repositório Institucional da UFU - Universidade Federal de Uberlândia (UFU) |
repository.mail.fl_str_mv |
diinf@dirbi.ufu.br |
_version_ |
1805569674317922304 |