Transverse cylindrical grinding of a eutectic alloy
Autor(a) principal: | |
---|---|
Data de Publicação: | 2003 |
Outros Autores: | , , , , , |
Tipo de documento: | Artigo |
Idioma: | eng |
Título da fonte: | Repositório Institucional da UNESP |
Texto Completo: | http://dx.doi.org/10.1590/S1678-58782003000100011 http://hdl.handle.net/11449/67170 |
Resumo: | We report herein on a comparison of the performance of two different grinding wheels (conventional and CBN) in the transverse cylindrical grinding of a eutectic alloy. Three cutting conditions were tested: rough, semi-finishing and finishing. The parameters of evaluation were the cutting force, roughness and wheel wear. The optimal cutting force and roughness values were obtained when grinding with the conventional wheel, due to the superior dressing operation performed under every cutting condition tested. Although the CBN wheel presented the best G ratio values, they were lower than expected owing to the inappropriate dressing operation applied. Excessive wheel corner wear was detected in both wheels, caused by the grinding kinematics (transverse grinding) employed. In terms of cutting force and roughness, the conventional wheel proved to be the better choice under the conditions tested. However, in terms of the G ratio, a cost analysis is crucial to determine whether the differences between the wheels justify the use of the CBN wheel, in which case the dressing operation requires improvement. |
id |
UNSP_0fb93350c1a302f957822ea8f990f5dd |
---|---|
oai_identifier_str |
oai:repositorio.unesp.br:11449/67170 |
network_acronym_str |
UNSP |
network_name_str |
Repositório Institucional da UNESP |
repository_id_str |
2946 |
spelling |
Transverse cylindrical grinding of a eutectic alloyDressingGrindingGrinding wheelPerformanceCuttingGrinding wheelsSuperalloysWheel dressingEutectic alloysGrinding (comminution)We report herein on a comparison of the performance of two different grinding wheels (conventional and CBN) in the transverse cylindrical grinding of a eutectic alloy. Three cutting conditions were tested: rough, semi-finishing and finishing. The parameters of evaluation were the cutting force, roughness and wheel wear. The optimal cutting force and roughness values were obtained when grinding with the conventional wheel, due to the superior dressing operation performed under every cutting condition tested. Although the CBN wheel presented the best G ratio values, they were lower than expected owing to the inappropriate dressing operation applied. Excessive wheel corner wear was detected in both wheels, caused by the grinding kinematics (transverse grinding) employed. In terms of cutting force and roughness, the conventional wheel proved to be the better choice under the conditions tested. However, in terms of the G ratio, a cost analysis is crucial to determine whether the differences between the wheels justify the use of the CBN wheel, in which case the dressing operation requires improvement.UNESP School of Engineering, Bauru, SPUSP - University of São Paulo, São Carlos, SPUNESP School of Engineering, Bauru, SPUniversidade Estadual Paulista (Unesp)Universidade de São Paulo (USP)Bianchi, E. C. [UNESP]Vargas, V. L. [UNESP]Magagnin, T. C. [UNESP]Monici, R. D. [UNESP]Vicari Filho, O. [UNESP]De Aguiar, P. R. [UNESP]Jannone da Silva, E.2014-05-27T11:20:36Z2014-05-27T11:20:36Z2003-01-01info:eu-repo/semantics/publishedVersioninfo:eu-repo/semantics/article79-84http://dx.doi.org/10.1590/S1678-58782003000100011Journal of the Brazilian Society of Mechanical Sciences and Engineering, v. 25, n. 1, p. 79-84, 2003.1678-5878http://hdl.handle.net/11449/6717010.1590/S1678-58782003000100011S1678-587820030001000112-s2.0-003844222210991520075749211455400309660081Scopusreponame:Repositório Institucional da UNESPinstname:Universidade Estadual Paulista (UNESP)instacron:UNESPengJournal of the Brazilian Society of Mechanical Sciences and Engineering1.6270,362info:eu-repo/semantics/openAccess2021-10-23T11:43:33Zoai:repositorio.unesp.br:11449/67170Repositório InstitucionalPUBhttp://repositorio.unesp.br/oai/requestopendoar:29462021-10-23T11:43:33Repositório Institucional da UNESP - Universidade Estadual Paulista (UNESP)false |
dc.title.none.fl_str_mv |
Transverse cylindrical grinding of a eutectic alloy |
title |
Transverse cylindrical grinding of a eutectic alloy |
spellingShingle |
Transverse cylindrical grinding of a eutectic alloy Bianchi, E. C. [UNESP] Dressing Grinding Grinding wheel Performance Cutting Grinding wheels Superalloys Wheel dressing Eutectic alloys Grinding (comminution) |
title_short |
Transverse cylindrical grinding of a eutectic alloy |
title_full |
Transverse cylindrical grinding of a eutectic alloy |
title_fullStr |
Transverse cylindrical grinding of a eutectic alloy |
title_full_unstemmed |
Transverse cylindrical grinding of a eutectic alloy |
title_sort |
Transverse cylindrical grinding of a eutectic alloy |
author |
Bianchi, E. C. [UNESP] |
author_facet |
Bianchi, E. C. [UNESP] Vargas, V. L. [UNESP] Magagnin, T. C. [UNESP] Monici, R. D. [UNESP] Vicari Filho, O. [UNESP] De Aguiar, P. R. [UNESP] Jannone da Silva, E. |
author_role |
author |
author2 |
Vargas, V. L. [UNESP] Magagnin, T. C. [UNESP] Monici, R. D. [UNESP] Vicari Filho, O. [UNESP] De Aguiar, P. R. [UNESP] Jannone da Silva, E. |
author2_role |
author author author author author author |
dc.contributor.none.fl_str_mv |
Universidade Estadual Paulista (Unesp) Universidade de São Paulo (USP) |
dc.contributor.author.fl_str_mv |
Bianchi, E. C. [UNESP] Vargas, V. L. [UNESP] Magagnin, T. C. [UNESP] Monici, R. D. [UNESP] Vicari Filho, O. [UNESP] De Aguiar, P. R. [UNESP] Jannone da Silva, E. |
dc.subject.por.fl_str_mv |
Dressing Grinding Grinding wheel Performance Cutting Grinding wheels Superalloys Wheel dressing Eutectic alloys Grinding (comminution) |
topic |
Dressing Grinding Grinding wheel Performance Cutting Grinding wheels Superalloys Wheel dressing Eutectic alloys Grinding (comminution) |
description |
We report herein on a comparison of the performance of two different grinding wheels (conventional and CBN) in the transverse cylindrical grinding of a eutectic alloy. Three cutting conditions were tested: rough, semi-finishing and finishing. The parameters of evaluation were the cutting force, roughness and wheel wear. The optimal cutting force and roughness values were obtained when grinding with the conventional wheel, due to the superior dressing operation performed under every cutting condition tested. Although the CBN wheel presented the best G ratio values, they were lower than expected owing to the inappropriate dressing operation applied. Excessive wheel corner wear was detected in both wheels, caused by the grinding kinematics (transverse grinding) employed. In terms of cutting force and roughness, the conventional wheel proved to be the better choice under the conditions tested. However, in terms of the G ratio, a cost analysis is crucial to determine whether the differences between the wheels justify the use of the CBN wheel, in which case the dressing operation requires improvement. |
publishDate |
2003 |
dc.date.none.fl_str_mv |
2003-01-01 2014-05-27T11:20:36Z 2014-05-27T11:20:36Z |
dc.type.status.fl_str_mv |
info:eu-repo/semantics/publishedVersion |
dc.type.driver.fl_str_mv |
info:eu-repo/semantics/article |
format |
article |
status_str |
publishedVersion |
dc.identifier.uri.fl_str_mv |
http://dx.doi.org/10.1590/S1678-58782003000100011 Journal of the Brazilian Society of Mechanical Sciences and Engineering, v. 25, n. 1, p. 79-84, 2003. 1678-5878 http://hdl.handle.net/11449/67170 10.1590/S1678-58782003000100011 S1678-58782003000100011 2-s2.0-0038442222 1099152007574921 1455400309660081 |
url |
http://dx.doi.org/10.1590/S1678-58782003000100011 http://hdl.handle.net/11449/67170 |
identifier_str_mv |
Journal of the Brazilian Society of Mechanical Sciences and Engineering, v. 25, n. 1, p. 79-84, 2003. 1678-5878 10.1590/S1678-58782003000100011 S1678-58782003000100011 2-s2.0-0038442222 1099152007574921 1455400309660081 |
dc.language.iso.fl_str_mv |
eng |
language |
eng |
dc.relation.none.fl_str_mv |
Journal of the Brazilian Society of Mechanical Sciences and Engineering 1.627 0,362 |
dc.rights.driver.fl_str_mv |
info:eu-repo/semantics/openAccess |
eu_rights_str_mv |
openAccess |
dc.format.none.fl_str_mv |
79-84 |
dc.source.none.fl_str_mv |
Scopus reponame:Repositório Institucional da UNESP instname:Universidade Estadual Paulista (UNESP) instacron:UNESP |
instname_str |
Universidade Estadual Paulista (UNESP) |
instacron_str |
UNESP |
institution |
UNESP |
reponame_str |
Repositório Institucional da UNESP |
collection |
Repositório Institucional da UNESP |
repository.name.fl_str_mv |
Repositório Institucional da UNESP - Universidade Estadual Paulista (UNESP) |
repository.mail.fl_str_mv |
|
_version_ |
1799965547406819328 |