Metodologia de projeto do conversor DAB aplicado a transformadores de estado sólido
Autor(a) principal: | |
---|---|
Data de Publicação: | 2014 |
Tipo de documento: | Tese |
Idioma: | por |
Título da fonte: | Manancial - Repositório Digital da UFSM |
Texto Completo: | http://repositorio.ufsm.br/handle/1/3685 |
Resumo: | This thesis presents a design methodology for the dual active bridge converter, that includes the influence of the nominal phase-shift angle in the behavior of the DAB converter for entire power and voltage ranges. The analysis presented focus on two important performance parameters of the DAB converter: the nonactive power and the limits of ZVS operation. The study of these two parameters results in a prior knowledge of the qualitative characteristics of the conduction and switching losses, respectively. Using this knowledge it is possible to optimize the converter operation considering the priorities of application performance. The experimental results were performed for three different projects nominal angles and three different input voltages for the whole load range, and they prove the feasibility of the proposed analysis. The analyse of the limit ZVS area took into account the switches intrinsic capacitances, and the dead time between the complementary switches. The DAB converter placed at a three-stage structure applied to solid state transformer, has voltage ripple at low frequency in their bus voltages because of the connection into the distribution network. Thus, it becomes possible to apply a low frequency burst mode modulation, without needing to oversize the bus capacitors. Three burst mode modulations are evaluated in simulation. The modulation which performed better results in simulation was implemented in practice, and the experimental results showed significant improvement in the converter´s efficiency when it is operating in light loads. Finally, a discussion of the parameters to be evaluated for the DAB converter´s design is proposed. |
id |
UFSM_012f936e2bf54a5f8ee123542066c455 |
---|---|
oai_identifier_str |
oai:repositorio.ufsm.br:1/3685 |
network_acronym_str |
UFSM |
network_name_str |
Manancial - Repositório Digital da UFSM |
repository_id_str |
|
spelling |
Metodologia de projeto do conversor DAB aplicado a transformadores de estado sólidoDesign methodology of the dual active bridge converter applied to solid state transformersConversores CC-CCConversor dual active bridgeEletrônica de potênciaTransformadores de estado sólidoDC-DC convertersDual active bridge converterPower electronicsSolid state transformersCNPQ::ENGENHARIAS::ENGENHARIA ELETRICAThis thesis presents a design methodology for the dual active bridge converter, that includes the influence of the nominal phase-shift angle in the behavior of the DAB converter for entire power and voltage ranges. The analysis presented focus on two important performance parameters of the DAB converter: the nonactive power and the limits of ZVS operation. The study of these two parameters results in a prior knowledge of the qualitative characteristics of the conduction and switching losses, respectively. Using this knowledge it is possible to optimize the converter operation considering the priorities of application performance. The experimental results were performed for three different projects nominal angles and three different input voltages for the whole load range, and they prove the feasibility of the proposed analysis. The analyse of the limit ZVS area took into account the switches intrinsic capacitances, and the dead time between the complementary switches. The DAB converter placed at a three-stage structure applied to solid state transformer, has voltage ripple at low frequency in their bus voltages because of the connection into the distribution network. Thus, it becomes possible to apply a low frequency burst mode modulation, without needing to oversize the bus capacitors. Three burst mode modulations are evaluated in simulation. The modulation which performed better results in simulation was implemented in practice, and the experimental results showed significant improvement in the converter´s efficiency when it is operating in light loads. Finally, a discussion of the parameters to be evaluated for the DAB converter´s design is proposed.Coordenação de Aperfeiçoamento de Pessoal de Nível SuperiorEsta tese de doutorado apresenta uma metodologia de projeto do conversor DAB, a qual inclui a influência do ângulo nominal de defasagem no comportamento do conversor DAB para toda faixa de potência e de tensão. Além disso, as análises focam em dois importantes parâmetros de desempenho do conversor DAB: a potência não ativa e os limites de operação com ZVS. O estudo destes dois parâmetros resulta em um conhecimento prévio das características qualitativas das perdas de condução e comutação, respectivamente. Através deste conhecimento é possível otimizar a operação do conversor considerando as prioridades de desempenho da aplicação. Os resultados experimentais, que comprovam as análises referentes à potência não ativa e aos limites de operação com ZVS, são realizados para três diferentes projetos de ângulos nominais e três diferentes tensões de entrada, para toda faixa de operação de carga. O estudo dos pontos de perda de ZVS considerou as capacitâncias intrínsecas dos interruptores e o tempo morto entre os interruptores complementares. O conversor DAB funcionando em uma estrutura de três estágios, aplicado a transformadores de estado sólido, apresenta ondulação de tensão em baixa frequência em seus barramentos, provinente da conexão da estrutura na rede de distribuição. Deste modo, torna-se possível a aplicação de modulações de baixa frequência do tipo burst, sem a necessidade de sobredimensionamento dos capacitores. Três modulações são realizadas e avaliadas em simulação. A modulação que apresentou melhores resultados em simulação foi implementada na prática, e os resultados experimentais mostraram melhora significativa da eficiência do conversor em baixas cargas. Por fim, uma discussão sobre as considerações a serem avaliadas nos parâmetros de projeto do conversor DAB é proposta.Universidade Federal de Santa MariaBREngenharia ElétricaUFSMPrograma de Pós-Graduação em Engenharia ElétricaDalla Costa, Marco Antôniohttp://buscatextual.cnpq.br/buscatextual/visualizacv.do?id=K4765177T4Rech, Cassianohttp://buscatextual.cnpq.br/buscatextual/visualizacv.do?id=K4767540A9Martins, Denizar Cruzhttp://lattes.cnpq.br/6156546664055944Pomilio, Jose Antenorhttp://buscatextual.cnpq.br/buscatextual/visualizacv.do?id=K4783454U0Pinheiro, José Reneshttp://buscatextual.cnpq.br/buscatextual/visualizacv.do?id=K4787136P4Kirsten, André Luís2017-05-192017-05-192014-08-01info:eu-repo/semantics/publishedVersioninfo:eu-repo/semantics/doctoralThesisapplication/pdfapplication/pdfKIRSTEN, André Luís. Design methodology of the dual active bridge converter applied to solid state transformers. 2014. 236 f. Tese (Doutorado em Engenharia Elétrica) - Universidade Federal de Santa Maria, Santa Maria, 2014.http://repositorio.ufsm.br/handle/1/3685porinfo:eu-repo/semantics/openAccessreponame:Manancial - Repositório Digital da UFSMinstname:Universidade Federal de Santa Maria (UFSM)instacron:UFSM2022-05-12T15:27:22Zoai:repositorio.ufsm.br:1/3685Biblioteca Digital de Teses e Dissertaçõeshttps://repositorio.ufsm.br/ONGhttps://repositorio.ufsm.br/oai/requestatendimento.sib@ufsm.br||tedebc@gmail.comopendoar:2022-05-12T15:27:22Manancial - Repositório Digital da UFSM - Universidade Federal de Santa Maria (UFSM)false |
dc.title.none.fl_str_mv |
Metodologia de projeto do conversor DAB aplicado a transformadores de estado sólido Design methodology of the dual active bridge converter applied to solid state transformers |
title |
Metodologia de projeto do conversor DAB aplicado a transformadores de estado sólido |
spellingShingle |
Metodologia de projeto do conversor DAB aplicado a transformadores de estado sólido Kirsten, André Luís Conversores CC-CC Conversor dual active bridge Eletrônica de potência Transformadores de estado sólido DC-DC converters Dual active bridge converter Power electronics Solid state transformers CNPQ::ENGENHARIAS::ENGENHARIA ELETRICA |
title_short |
Metodologia de projeto do conversor DAB aplicado a transformadores de estado sólido |
title_full |
Metodologia de projeto do conversor DAB aplicado a transformadores de estado sólido |
title_fullStr |
Metodologia de projeto do conversor DAB aplicado a transformadores de estado sólido |
title_full_unstemmed |
Metodologia de projeto do conversor DAB aplicado a transformadores de estado sólido |
title_sort |
Metodologia de projeto do conversor DAB aplicado a transformadores de estado sólido |
author |
Kirsten, André Luís |
author_facet |
Kirsten, André Luís |
author_role |
author |
dc.contributor.none.fl_str_mv |
Dalla Costa, Marco Antônio http://buscatextual.cnpq.br/buscatextual/visualizacv.do?id=K4765177T4 Rech, Cassiano http://buscatextual.cnpq.br/buscatextual/visualizacv.do?id=K4767540A9 Martins, Denizar Cruz http://lattes.cnpq.br/6156546664055944 Pomilio, Jose Antenor http://buscatextual.cnpq.br/buscatextual/visualizacv.do?id=K4783454U0 Pinheiro, José Renes http://buscatextual.cnpq.br/buscatextual/visualizacv.do?id=K4787136P4 |
dc.contributor.author.fl_str_mv |
Kirsten, André Luís |
dc.subject.por.fl_str_mv |
Conversores CC-CC Conversor dual active bridge Eletrônica de potência Transformadores de estado sólido DC-DC converters Dual active bridge converter Power electronics Solid state transformers CNPQ::ENGENHARIAS::ENGENHARIA ELETRICA |
topic |
Conversores CC-CC Conversor dual active bridge Eletrônica de potência Transformadores de estado sólido DC-DC converters Dual active bridge converter Power electronics Solid state transformers CNPQ::ENGENHARIAS::ENGENHARIA ELETRICA |
description |
This thesis presents a design methodology for the dual active bridge converter, that includes the influence of the nominal phase-shift angle in the behavior of the DAB converter for entire power and voltage ranges. The analysis presented focus on two important performance parameters of the DAB converter: the nonactive power and the limits of ZVS operation. The study of these two parameters results in a prior knowledge of the qualitative characteristics of the conduction and switching losses, respectively. Using this knowledge it is possible to optimize the converter operation considering the priorities of application performance. The experimental results were performed for three different projects nominal angles and three different input voltages for the whole load range, and they prove the feasibility of the proposed analysis. The analyse of the limit ZVS area took into account the switches intrinsic capacitances, and the dead time between the complementary switches. The DAB converter placed at a three-stage structure applied to solid state transformer, has voltage ripple at low frequency in their bus voltages because of the connection into the distribution network. Thus, it becomes possible to apply a low frequency burst mode modulation, without needing to oversize the bus capacitors. Three burst mode modulations are evaluated in simulation. The modulation which performed better results in simulation was implemented in practice, and the experimental results showed significant improvement in the converter´s efficiency when it is operating in light loads. Finally, a discussion of the parameters to be evaluated for the DAB converter´s design is proposed. |
publishDate |
2014 |
dc.date.none.fl_str_mv |
2014-08-01 2017-05-19 2017-05-19 |
dc.type.status.fl_str_mv |
info:eu-repo/semantics/publishedVersion |
dc.type.driver.fl_str_mv |
info:eu-repo/semantics/doctoralThesis |
format |
doctoralThesis |
status_str |
publishedVersion |
dc.identifier.uri.fl_str_mv |
KIRSTEN, André Luís. Design methodology of the dual active bridge converter applied to solid state transformers. 2014. 236 f. Tese (Doutorado em Engenharia Elétrica) - Universidade Federal de Santa Maria, Santa Maria, 2014. http://repositorio.ufsm.br/handle/1/3685 |
identifier_str_mv |
KIRSTEN, André Luís. Design methodology of the dual active bridge converter applied to solid state transformers. 2014. 236 f. Tese (Doutorado em Engenharia Elétrica) - Universidade Federal de Santa Maria, Santa Maria, 2014. |
url |
http://repositorio.ufsm.br/handle/1/3685 |
dc.language.iso.fl_str_mv |
por |
language |
por |
dc.rights.driver.fl_str_mv |
info:eu-repo/semantics/openAccess |
eu_rights_str_mv |
openAccess |
dc.format.none.fl_str_mv |
application/pdf application/pdf |
dc.publisher.none.fl_str_mv |
Universidade Federal de Santa Maria BR Engenharia Elétrica UFSM Programa de Pós-Graduação em Engenharia Elétrica |
publisher.none.fl_str_mv |
Universidade Federal de Santa Maria BR Engenharia Elétrica UFSM Programa de Pós-Graduação em Engenharia Elétrica |
dc.source.none.fl_str_mv |
reponame:Manancial - Repositório Digital da UFSM instname:Universidade Federal de Santa Maria (UFSM) instacron:UFSM |
instname_str |
Universidade Federal de Santa Maria (UFSM) |
instacron_str |
UFSM |
institution |
UFSM |
reponame_str |
Manancial - Repositório Digital da UFSM |
collection |
Manancial - Repositório Digital da UFSM |
repository.name.fl_str_mv |
Manancial - Repositório Digital da UFSM - Universidade Federal de Santa Maria (UFSM) |
repository.mail.fl_str_mv |
atendimento.sib@ufsm.br||tedebc@gmail.com |
_version_ |
1805922160822190080 |