Avaliação do desempenho de fluidos dielétricos no processo de usinagem por descargas elétricas
Autor(a) principal: | |
---|---|
Data de Publicação: | 2001 |
Tipo de documento: | Dissertação |
Idioma: | por |
Título da fonte: | Repositório Institucional da UFU |
Texto Completo: | https://repositorio.ufu.br/handle/123456789/14876 |
Resumo: | The Electrical Discharge Machining process is very useful while machining very hard materials, which are very difficult to be machined by traditional processes, while can make complex geometries and minimum dimensions. One of the materials that are used in this process is highspeed steels, which are very hard and has a high mechanical resistance. The main objective of this work is the study of performance of different dielectric fluids used in EDM in different cut conditions in terms or metal removal rate (MMR) and wear ratio (WR) roughness parameter (Ra). A discuss of the most important factors that can produce different performance when machining with this process is presented. Five tests with different types of dielectric fluids using a cooper tool were carried out. Was noticed different performance between the fluids, which all the other conditions of operation were unchanged. According to the fluid the workpiece presented less roughness and a higher MMR in some cases. In other cases, a higher MMR produced in the other hand a recast layer less uniform. The most important conclusion of this work is about kerosene, which costs 3 times less than the specific dielectric fluids for EDM, presented worst finishing surfaces and not too high MMR as expected, despite all the risks for the operator. |
id |
UFU_80bc0e61e1ea4ab5a34d9ac40beb3db1 |
---|---|
oai_identifier_str |
oai:repositorio.ufu.br:123456789/14876 |
network_acronym_str |
UFU |
network_name_str |
Repositório Institucional da UFU |
repository_id_str |
|
spelling |
Avaliação do desempenho de fluidos dielétricos no processo de usinagem por descargas elétricasEvaluation of performance of dielectric fluids for electrical discharge machining processEDMFluidos dielétricosTRMTopografia e rugosidadeUsinagem por eletroerosãoProcessos de fabricaçãoMicrografiaEDMDielectric fluidsMMRRoughness and topographyCNPQ::ENGENHARIAS::ENGENHARIA MECANICAThe Electrical Discharge Machining process is very useful while machining very hard materials, which are very difficult to be machined by traditional processes, while can make complex geometries and minimum dimensions. One of the materials that are used in this process is highspeed steels, which are very hard and has a high mechanical resistance. The main objective of this work is the study of performance of different dielectric fluids used in EDM in different cut conditions in terms or metal removal rate (MMR) and wear ratio (WR) roughness parameter (Ra). A discuss of the most important factors that can produce different performance when machining with this process is presented. Five tests with different types of dielectric fluids using a cooper tool were carried out. Was noticed different performance between the fluids, which all the other conditions of operation were unchanged. According to the fluid the workpiece presented less roughness and a higher MMR in some cases. In other cases, a higher MMR produced in the other hand a recast layer less uniform. The most important conclusion of this work is about kerosene, which costs 3 times less than the specific dielectric fluids for EDM, presented worst finishing surfaces and not too high MMR as expected, despite all the risks for the operator.Universidade Federal de UberlândiaMestre em Engenharia MecânicaO processo de Usinagem por Descargas Elétricas é muito utilizado na usinagem de materiais de elevada dureza, que são difíceis de serem usinados por processos convencionais, além de permitir a confecção de geometrias bem complexas e de dimensões diminutas. Um dos materiais que são largamente usinados por EDM (Electrical Discharge Machining) é o aço-ferramenta ABNT M2, que apresenta grande versatilidade, combinando excelente tenacidade, dureza e resistência a abrasão, muito indicado para confecção de matrizes de estampagem profundas e outras ferramentas de deformação plástica à frio. O objetivo principal deste trabalho é o estudo do desempenho de diferentes tipos de fluidos dielétricos em três regimes pré-estabelecidos com relação à rugosidade média aritmética (Ra), taxa de remoção de material (TRM), relação de desgaste (RD) e rugosidade; além de discutir e analisar os mais importantes fatores que influenciam no processo de usinagem por descargas elétricas. Os diversos fluidos dielétricos utilizados possibilitam diferentes condições de usinagem e muito pouco se sabe sobre qual o fluido mais indicado para operações de acabamento ou desbaste. Foram feitos ensaios com 5 tipos diferentes de fluidos dielétricos e com uma ferramenta de cobre. Verificou-se que há diferenças importantes quando usina-se com fluidos diferentes, mantendo-se constantes todas as demais condições de operação. Notou-se que quando utilizando-se um determinado fluido a peça apresentou uma menor rugosidade e também uma maior TRM em alguns casos. Já em outros casos, uma maior TRM ocasionou em contrapartida uma Camada Refundida menos uniforme. Porém, a maior conclusão desse trabalho foi a de que o querosene, apesar de ser até 3 vezes mais barato que os demais fluidos, apresentou piores acabamentos superficiais e TRM não tão grandes quanto o esperado, além de maiores riscos ao operador.Universidade Federal de UberlândiaBRPrograma de Pós-graduação em Engenharia MecânicaEngenhariasUFUSilva, Evaldo Malaquias dahttp://buscatextual.cnpq.br/buscatextual/visualizacv.do?id=K4703559H3Raslan, Alberto Arnaldohttp://buscatextual.cnpq.br/buscatextual/visualizacv.do?id=K4787991J4Cruz, ClaudionorSilva, Márcio Bacci dahttp://buscatextual.cnpq.br/buscatextual/visualizacv.do?id=K4785913J0Arantes, Luciano José2016-06-22T18:40:13Z2006-02-022016-06-22T18:40:13Z2001-12-14info:eu-repo/semantics/publishedVersioninfo:eu-repo/semantics/masterThesisapplication/pdfapplication/pdfapplication/pdfapplication/pdfapplication/pdfARANTES, Luciano José. Evaluation of performance of dielectric fluids for electrical discharge machining process. 2001. 86 f. Dissertação (Mestrado em Engenharias) - Universidade Federal de Uberlândia, Uberlândia, 2001.https://repositorio.ufu.br/handle/123456789/14876porinfo:eu-repo/semantics/openAccessreponame:Repositório Institucional da UFUinstname:Universidade Federal de Uberlândia (UFU)instacron:UFU2017-10-11T15:06:51Zoai:repositorio.ufu.br:123456789/14876Repositório InstitucionalONGhttp://repositorio.ufu.br/oai/requestdiinf@dirbi.ufu.bropendoar:2017-10-11T15:06:51Repositório Institucional da UFU - Universidade Federal de Uberlândia (UFU)false |
dc.title.none.fl_str_mv |
Avaliação do desempenho de fluidos dielétricos no processo de usinagem por descargas elétricas Evaluation of performance of dielectric fluids for electrical discharge machining process |
title |
Avaliação do desempenho de fluidos dielétricos no processo de usinagem por descargas elétricas |
spellingShingle |
Avaliação do desempenho de fluidos dielétricos no processo de usinagem por descargas elétricas Arantes, Luciano José EDM Fluidos dielétricos TRM Topografia e rugosidade Usinagem por eletroerosão Processos de fabricação Micrografia EDM Dielectric fluids MMR Roughness and topography CNPQ::ENGENHARIAS::ENGENHARIA MECANICA |
title_short |
Avaliação do desempenho de fluidos dielétricos no processo de usinagem por descargas elétricas |
title_full |
Avaliação do desempenho de fluidos dielétricos no processo de usinagem por descargas elétricas |
title_fullStr |
Avaliação do desempenho de fluidos dielétricos no processo de usinagem por descargas elétricas |
title_full_unstemmed |
Avaliação do desempenho de fluidos dielétricos no processo de usinagem por descargas elétricas |
title_sort |
Avaliação do desempenho de fluidos dielétricos no processo de usinagem por descargas elétricas |
author |
Arantes, Luciano José |
author_facet |
Arantes, Luciano José |
author_role |
author |
dc.contributor.none.fl_str_mv |
Silva, Evaldo Malaquias da http://buscatextual.cnpq.br/buscatextual/visualizacv.do?id=K4703559H3 Raslan, Alberto Arnaldo http://buscatextual.cnpq.br/buscatextual/visualizacv.do?id=K4787991J4 Cruz, Claudionor Silva, Márcio Bacci da http://buscatextual.cnpq.br/buscatextual/visualizacv.do?id=K4785913J0 |
dc.contributor.author.fl_str_mv |
Arantes, Luciano José |
dc.subject.por.fl_str_mv |
EDM Fluidos dielétricos TRM Topografia e rugosidade Usinagem por eletroerosão Processos de fabricação Micrografia EDM Dielectric fluids MMR Roughness and topography CNPQ::ENGENHARIAS::ENGENHARIA MECANICA |
topic |
EDM Fluidos dielétricos TRM Topografia e rugosidade Usinagem por eletroerosão Processos de fabricação Micrografia EDM Dielectric fluids MMR Roughness and topography CNPQ::ENGENHARIAS::ENGENHARIA MECANICA |
description |
The Electrical Discharge Machining process is very useful while machining very hard materials, which are very difficult to be machined by traditional processes, while can make complex geometries and minimum dimensions. One of the materials that are used in this process is highspeed steels, which are very hard and has a high mechanical resistance. The main objective of this work is the study of performance of different dielectric fluids used in EDM in different cut conditions in terms or metal removal rate (MMR) and wear ratio (WR) roughness parameter (Ra). A discuss of the most important factors that can produce different performance when machining with this process is presented. Five tests with different types of dielectric fluids using a cooper tool were carried out. Was noticed different performance between the fluids, which all the other conditions of operation were unchanged. According to the fluid the workpiece presented less roughness and a higher MMR in some cases. In other cases, a higher MMR produced in the other hand a recast layer less uniform. The most important conclusion of this work is about kerosene, which costs 3 times less than the specific dielectric fluids for EDM, presented worst finishing surfaces and not too high MMR as expected, despite all the risks for the operator. |
publishDate |
2001 |
dc.date.none.fl_str_mv |
2001-12-14 2006-02-02 2016-06-22T18:40:13Z 2016-06-22T18:40:13Z |
dc.type.status.fl_str_mv |
info:eu-repo/semantics/publishedVersion |
dc.type.driver.fl_str_mv |
info:eu-repo/semantics/masterThesis |
format |
masterThesis |
status_str |
publishedVersion |
dc.identifier.uri.fl_str_mv |
ARANTES, Luciano José. Evaluation of performance of dielectric fluids for electrical discharge machining process. 2001. 86 f. Dissertação (Mestrado em Engenharias) - Universidade Federal de Uberlândia, Uberlândia, 2001. https://repositorio.ufu.br/handle/123456789/14876 |
identifier_str_mv |
ARANTES, Luciano José. Evaluation of performance of dielectric fluids for electrical discharge machining process. 2001. 86 f. Dissertação (Mestrado em Engenharias) - Universidade Federal de Uberlândia, Uberlândia, 2001. |
url |
https://repositorio.ufu.br/handle/123456789/14876 |
dc.language.iso.fl_str_mv |
por |
language |
por |
dc.rights.driver.fl_str_mv |
info:eu-repo/semantics/openAccess |
eu_rights_str_mv |
openAccess |
dc.format.none.fl_str_mv |
application/pdf application/pdf application/pdf application/pdf application/pdf |
dc.publisher.none.fl_str_mv |
Universidade Federal de Uberlândia BR Programa de Pós-graduação em Engenharia Mecânica Engenharias UFU |
publisher.none.fl_str_mv |
Universidade Federal de Uberlândia BR Programa de Pós-graduação em Engenharia Mecânica Engenharias UFU |
dc.source.none.fl_str_mv |
reponame:Repositório Institucional da UFU instname:Universidade Federal de Uberlândia (UFU) instacron:UFU |
instname_str |
Universidade Federal de Uberlândia (UFU) |
instacron_str |
UFU |
institution |
UFU |
reponame_str |
Repositório Institucional da UFU |
collection |
Repositório Institucional da UFU |
repository.name.fl_str_mv |
Repositório Institucional da UFU - Universidade Federal de Uberlândia (UFU) |
repository.mail.fl_str_mv |
diinf@dirbi.ufu.br |
_version_ |
1805569578960420864 |