Aprofundamento em técnicas de levantamento de resposta em frequência de TPs

Detalhes bibliográficos
Autor(a) principal: Araújo, Paula Angélica de
Data de Publicação: 2023
Tipo de documento: Trabalho de conclusão de curso
Idioma: por
Título da fonte: Repositório Institucional da UFU
Texto Completo: https://repositorio.ufu.br/handle/123456789/38678
Resumo: With the increasing use of non-linear equipment, there is also concern about the behavior of the electrical power system in the face of possible harmonic distortions caused by these loads and their respective effects. Thus, studies are developed regarding techniques for measuring and quantifying these harmonic distortions in the context of campaigns to measure Power Quality indicators. When dealing with measurement systems, it may be necessary to use voltage transducers (VTs), depending on the voltage level to be measured. However, it is known that some types of VTs may not present a linear response in the frequency spectrum. Since the inductive voltage transformer is a device widely used for this purpose, studies to obtain the frequency response of this element are of great importance, as it is known in the literature that harmonic distortions may have impact on its accuracy of measurements. As there are several proposed procedures to perform the frequency response test, the present work intends to perform two out of these procedures found in Brazilian regulations, in order to analyze the main differences between the test procedures, and the results obtained from them. In this context, the first procedure consists in applying the VT primary with harmonic voltage lower than its rated value. On the other hand, the second procedure is characterized by the applying rated fundamental voltage plus harmonic components. After carrying out the tests, the frequency response curves were drawn, it was verified that the results obtained by the tests differed from each other, and that the VT response from the test with the fundamental voltage plus harmonic components showed non-linear characteristics, violating the limits for higher precision instruments suggested by IEC/TR 61869-103 for some harmonic orders. The test with a voltage lower than the rated remained within the suggested limits. Therefore, it is concluded that it is necessary to perform the test that considers the presence of rated fundamental voltage despite its greater difficulty in carrying out it in the field, since it leads to more accurate results along the harmonic spectrum, showing the real impacts of non-linearity of inductive voltage transformers.
id UFU_89c4596eebe2a3f696f8fc69b9772d8a
oai_identifier_str oai:repositorio.ufu.br:123456789/38678
network_acronym_str UFU
network_name_str Repositório Institucional da UFU
repository_id_str
spelling Aprofundamento em técnicas de levantamento de resposta em frequência de TPsDeepening in VTs frequency response techniquesNão linearidadeNon-linearityResposta em frequênciaFrequency responseDistorção harmônicaHarmonic distortionQualidade da energia elétricaPower qualityTransformadores de potencialVoltage transformersTransformador de potencial indutivo.Inductive voltage transformerCNPQ::ENGENHARIAS::ENGENHARIA ELETRICA::SISTEMAS ELETRICOS DE POTENCIAWith the increasing use of non-linear equipment, there is also concern about the behavior of the electrical power system in the face of possible harmonic distortions caused by these loads and their respective effects. Thus, studies are developed regarding techniques for measuring and quantifying these harmonic distortions in the context of campaigns to measure Power Quality indicators. When dealing with measurement systems, it may be necessary to use voltage transducers (VTs), depending on the voltage level to be measured. However, it is known that some types of VTs may not present a linear response in the frequency spectrum. Since the inductive voltage transformer is a device widely used for this purpose, studies to obtain the frequency response of this element are of great importance, as it is known in the literature that harmonic distortions may have impact on its accuracy of measurements. As there are several proposed procedures to perform the frequency response test, the present work intends to perform two out of these procedures found in Brazilian regulations, in order to analyze the main differences between the test procedures, and the results obtained from them. In this context, the first procedure consists in applying the VT primary with harmonic voltage lower than its rated value. On the other hand, the second procedure is characterized by the applying rated fundamental voltage plus harmonic components. After carrying out the tests, the frequency response curves were drawn, it was verified that the results obtained by the tests differed from each other, and that the VT response from the test with the fundamental voltage plus harmonic components showed non-linear characteristics, violating the limits for higher precision instruments suggested by IEC/TR 61869-103 for some harmonic orders. The test with a voltage lower than the rated remained within the suggested limits. Therefore, it is concluded that it is necessary to perform the test that considers the presence of rated fundamental voltage despite its greater difficulty in carrying out it in the field, since it leads to more accurate results along the harmonic spectrum, showing the real impacts of non-linearity of inductive voltage transformers.Pesquisa sem auxílio de agências de fomentoTrabalho de Conclusão de Curso (Graduação)Com a crescente utilização de equipamentos não lineares, surge também a preocupação a respeito do comportamento do sistema elétrico de potência diante das possíveis distorções harmônicas causadas por estas cargas e seus respectivos efeitos. Assim, são desenvolvidos estudos a respeito de técnicas de medição e de quantificação dessas distorções harmônicas no contexto de campanhas de medição de indicadores de Qualidade da Energia Elétrica. Ao se tratar de sistemas de medição, pode ser necessário o uso de transdutores de potencial (TPs), a depender do nível de tensão a ser medido. Entretanto sabe-se que alguns tipos de TPs podem não apresentar resposta linear ao longo do espectro de frequência. Sendo o transformador de potencial indutivo um equipamento amplamente utilizado para este fim, tem-se que os estudos para o levantamento da resposta em frequência desse elemento são de grande relevância, pois é conhecido na literatura que as distorções harmônicas podem ter impacto sobre a precisão de suas medições. Como existem vários procedimentos propostos para a realização do teste de resposta em frequência, o presente trabalho busca realizar dois dos procedimentos encontrados nas normativas brasileiras, a fim de analisar as principais diferenças entre os procedimentos dos ensaios, e os resultados obtidos a partir deles. Nesse contexto, o primeiro procedimento consiste na alimentação do primário do TPI com uma tensão harmônica menor do que o seu valor nominal. Já o segundo procedimento é caracterizado pela aplicação da tensão fundamental nominal acrescida de componentes harmônicas. Da realização dos ensaios, foram levantadas as curvas de resposta em frequência, onde foi verificado que os resultados obtidos pelos ensaios apresentaram divergências entre si, sendo que a resposta do TPI a partir do ensaio com a tensão fundamental acrescida de componentes harmônicas se mostrou com características não lineares, violando os limites para instrumentos de maior precisão sugeridos pela IEC/TR 61869-103 para algumas ordens harmônicas. Já o ensaio com uma tensão menor do que a nominal se manteve entre os limites sugeridos. Dessa forma, conclui-se a necessidade de executar o ensaio que considera a presença de tensão fundamental nominal apesar de sua maior dificuldade de realização em campo, uma vez que ele leva a resultados mais precisos ao longo do espectro harmônico, mostrando os reais impactos da não linearidade dos transformadores de potencial indutivo.Universidade Federal de UberlândiaBrasilEngenharia ElétricaGianesini, Bárbara MoraisSantos, Ivan Nuneshttp://lattes.cnpq.br/0590030130547029Gregory, Raquel Cristina Filiagihttp://lattes.cnpq.br/9318165631771596X, XXAraújo, Paula Angélica de2023-07-18T13:30:40Z2023-07-18T13:30:40Z2023-06-19info:eu-repo/semantics/publishedVersioninfo:eu-repo/semantics/bachelorThesisapplication/pdfARAÚJO, Paula Angélica de. Aprofundamento em técnicas de levantamento de resposta em frequência de TPs. 2023. 59 f. Trabalho de Conclusão de Curso (Graduação em Engenharia Elétrica) – Universidade Federal de Uberlândia, Uberlândia, 2023.https://repositorio.ufu.br/handle/123456789/38678porinfo:eu-repo/semantics/openAccessreponame:Repositório Institucional da UFUinstname:Universidade Federal de Uberlândia (UFU)instacron:UFU2023-07-19T06:22:45Zoai:repositorio.ufu.br:123456789/38678Repositório InstitucionalONGhttp://repositorio.ufu.br/oai/requestdiinf@dirbi.ufu.bropendoar:2023-07-19T06:22:45Repositório Institucional da UFU - Universidade Federal de Uberlândia (UFU)false
dc.title.none.fl_str_mv Aprofundamento em técnicas de levantamento de resposta em frequência de TPs
Deepening in VTs frequency response techniques
title Aprofundamento em técnicas de levantamento de resposta em frequência de TPs
spellingShingle Aprofundamento em técnicas de levantamento de resposta em frequência de TPs
Araújo, Paula Angélica de
Não linearidade
Non-linearity
Resposta em frequência
Frequency response
Distorção harmônica
Harmonic distortion
Qualidade da energia elétrica
Power quality
Transformadores de potencial
Voltage transformers
Transformador de potencial indutivo.
Inductive voltage transformer
CNPQ::ENGENHARIAS::ENGENHARIA ELETRICA::SISTEMAS ELETRICOS DE POTENCIA
title_short Aprofundamento em técnicas de levantamento de resposta em frequência de TPs
title_full Aprofundamento em técnicas de levantamento de resposta em frequência de TPs
title_fullStr Aprofundamento em técnicas de levantamento de resposta em frequência de TPs
title_full_unstemmed Aprofundamento em técnicas de levantamento de resposta em frequência de TPs
title_sort Aprofundamento em técnicas de levantamento de resposta em frequência de TPs
author Araújo, Paula Angélica de
author_facet Araújo, Paula Angélica de
author_role author
dc.contributor.none.fl_str_mv Gianesini, Bárbara Morais
Santos, Ivan Nunes
http://lattes.cnpq.br/0590030130547029
Gregory, Raquel Cristina Filiagi
http://lattes.cnpq.br/9318165631771596
X, X
X
dc.contributor.author.fl_str_mv Araújo, Paula Angélica de
dc.subject.por.fl_str_mv Não linearidade
Non-linearity
Resposta em frequência
Frequency response
Distorção harmônica
Harmonic distortion
Qualidade da energia elétrica
Power quality
Transformadores de potencial
Voltage transformers
Transformador de potencial indutivo.
Inductive voltage transformer
CNPQ::ENGENHARIAS::ENGENHARIA ELETRICA::SISTEMAS ELETRICOS DE POTENCIA
topic Não linearidade
Non-linearity
Resposta em frequência
Frequency response
Distorção harmônica
Harmonic distortion
Qualidade da energia elétrica
Power quality
Transformadores de potencial
Voltage transformers
Transformador de potencial indutivo.
Inductive voltage transformer
CNPQ::ENGENHARIAS::ENGENHARIA ELETRICA::SISTEMAS ELETRICOS DE POTENCIA
description With the increasing use of non-linear equipment, there is also concern about the behavior of the electrical power system in the face of possible harmonic distortions caused by these loads and their respective effects. Thus, studies are developed regarding techniques for measuring and quantifying these harmonic distortions in the context of campaigns to measure Power Quality indicators. When dealing with measurement systems, it may be necessary to use voltage transducers (VTs), depending on the voltage level to be measured. However, it is known that some types of VTs may not present a linear response in the frequency spectrum. Since the inductive voltage transformer is a device widely used for this purpose, studies to obtain the frequency response of this element are of great importance, as it is known in the literature that harmonic distortions may have impact on its accuracy of measurements. As there are several proposed procedures to perform the frequency response test, the present work intends to perform two out of these procedures found in Brazilian regulations, in order to analyze the main differences between the test procedures, and the results obtained from them. In this context, the first procedure consists in applying the VT primary with harmonic voltage lower than its rated value. On the other hand, the second procedure is characterized by the applying rated fundamental voltage plus harmonic components. After carrying out the tests, the frequency response curves were drawn, it was verified that the results obtained by the tests differed from each other, and that the VT response from the test with the fundamental voltage plus harmonic components showed non-linear characteristics, violating the limits for higher precision instruments suggested by IEC/TR 61869-103 for some harmonic orders. The test with a voltage lower than the rated remained within the suggested limits. Therefore, it is concluded that it is necessary to perform the test that considers the presence of rated fundamental voltage despite its greater difficulty in carrying out it in the field, since it leads to more accurate results along the harmonic spectrum, showing the real impacts of non-linearity of inductive voltage transformers.
publishDate 2023
dc.date.none.fl_str_mv 2023-07-18T13:30:40Z
2023-07-18T13:30:40Z
2023-06-19
dc.type.status.fl_str_mv info:eu-repo/semantics/publishedVersion
dc.type.driver.fl_str_mv info:eu-repo/semantics/bachelorThesis
format bachelorThesis
status_str publishedVersion
dc.identifier.uri.fl_str_mv ARAÚJO, Paula Angélica de. Aprofundamento em técnicas de levantamento de resposta em frequência de TPs. 2023. 59 f. Trabalho de Conclusão de Curso (Graduação em Engenharia Elétrica) – Universidade Federal de Uberlândia, Uberlândia, 2023.
https://repositorio.ufu.br/handle/123456789/38678
identifier_str_mv ARAÚJO, Paula Angélica de. Aprofundamento em técnicas de levantamento de resposta em frequência de TPs. 2023. 59 f. Trabalho de Conclusão de Curso (Graduação em Engenharia Elétrica) – Universidade Federal de Uberlândia, Uberlândia, 2023.
url https://repositorio.ufu.br/handle/123456789/38678
dc.language.iso.fl_str_mv por
language por
dc.rights.driver.fl_str_mv info:eu-repo/semantics/openAccess
eu_rights_str_mv openAccess
dc.format.none.fl_str_mv application/pdf
dc.publisher.none.fl_str_mv Universidade Federal de Uberlândia
Brasil
Engenharia Elétrica
publisher.none.fl_str_mv Universidade Federal de Uberlândia
Brasil
Engenharia Elétrica
dc.source.none.fl_str_mv reponame:Repositório Institucional da UFU
instname:Universidade Federal de Uberlândia (UFU)
instacron:UFU
instname_str Universidade Federal de Uberlândia (UFU)
instacron_str UFU
institution UFU
reponame_str Repositório Institucional da UFU
collection Repositório Institucional da UFU
repository.name.fl_str_mv Repositório Institucional da UFU - Universidade Federal de Uberlândia (UFU)
repository.mail.fl_str_mv diinf@dirbi.ufu.br
_version_ 1805569686051487744