Influence of the anodization electrical mode on the final properties of electrocolored and sealed anodic films prepared on 1050 aluminum alloy
Autor(a) principal: | |
---|---|
Data de Publicação: | 2022 |
Outros Autores: | , |
Tipo de documento: | Artigo |
Idioma: | eng |
Título da fonte: | Repositório Institucional da UNESP |
Texto Completo: | http://dx.doi.org/10.1016/j.matchemphys.2022.126369 http://hdl.handle.net/11449/240282 |
Resumo: | The present study focused on the preparation of colored coatings on 1050 aluminum substrate using a four-step process including pretreatments, anodization, electrocoloring and hydrothermal sealing. Anodization of aluminum susbtrates can be usually performed either in potentiostatic mode or galvanostatic mode. The aim here was to study the influence of the electrical anodization mode (ideally with similar film thicknesses) and the influence of the alternating voltage applied during subsequent coloring on the final coating properties (color, hardness and anti-corrosion performance). Scanning electron microscopies (SEM and FEG-SEM) were used to obtain surface and cross-sectional views of the final coatings, and estimate the average pore diameter, while layer thicknesses (i.e. barrier, porous and sealing layers) were evaluated using different analytical techniques. Final coatings properties (i.e. hardness, color, electrical and corrosion resistance) were then studied. In particular, corrosion resistance was analyzed by electrochemical impedance spectroscopy (EIS) and potentiodynamic polarization. For both electrical anodization modes, similar coating thicknesses were obtained experimentally, while average pore diameter of the anodic films were of the same order of magnitude. For each electrical anodization mode, deeper color was obtained for optimum coloring voltage. However, the deeper colors obtained were associated with the lower coating hardness. Furthermore, based on total resistance values, coatings resulting from galvanostatic anodization have enhanced corrosion resistance than samples prepared by potentiostatic anodization. However, EIS analysis agreed with the results shown by polarization curves, highlighting that in such experimental conditions, coloring using high alternating voltage can be detrimental to the anticorrosion properties of such coatings. |
id |
UNSP_1f8981d916eef0cf0b8ca655d43e0974 |
---|---|
oai_identifier_str |
oai:repositorio.unesp.br:11449/240282 |
network_acronym_str |
UNSP |
network_name_str |
Repositório Institucional da UNESP |
repository_id_str |
2946 |
spelling |
Influence of the anodization electrical mode on the final properties of electrocolored and sealed anodic films prepared on 1050 aluminum alloyAluminumAnodizationElectrocoloringGalvanostatic modePotentiostatic modeThe present study focused on the preparation of colored coatings on 1050 aluminum substrate using a four-step process including pretreatments, anodization, electrocoloring and hydrothermal sealing. Anodization of aluminum susbtrates can be usually performed either in potentiostatic mode or galvanostatic mode. The aim here was to study the influence of the electrical anodization mode (ideally with similar film thicknesses) and the influence of the alternating voltage applied during subsequent coloring on the final coating properties (color, hardness and anti-corrosion performance). Scanning electron microscopies (SEM and FEG-SEM) were used to obtain surface and cross-sectional views of the final coatings, and estimate the average pore diameter, while layer thicknesses (i.e. barrier, porous and sealing layers) were evaluated using different analytical techniques. Final coatings properties (i.e. hardness, color, electrical and corrosion resistance) were then studied. In particular, corrosion resistance was analyzed by electrochemical impedance spectroscopy (EIS) and potentiodynamic polarization. For both electrical anodization modes, similar coating thicknesses were obtained experimentally, while average pore diameter of the anodic films were of the same order of magnitude. For each electrical anodization mode, deeper color was obtained for optimum coloring voltage. However, the deeper colors obtained were associated with the lower coating hardness. Furthermore, based on total resistance values, coatings resulting from galvanostatic anodization have enhanced corrosion resistance than samples prepared by potentiostatic anodization. However, EIS analysis agreed with the results shown by polarization curves, highlighting that in such experimental conditions, coloring using high alternating voltage can be detrimental to the anticorrosion properties of such coatings.Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)UNESP – São Paulo State University São João da Boa Vista Campus, Av. Profa. Isette Corrêa Fontão 505, Jardim Das FloresCIRIMAT Université de Toulouse CNRS UT3 Paul Sabatier Bât. CIRIMAT, 118 Route de NarbonneUNESP – São Paulo State University São João da Boa Vista Campus, Av. Profa. Isette Corrêa Fontão 505, Jardim Das FloresFAPESP: 2010/11492-3Universidade Estadual Paulista (UNESP)Bât. CIRIMATRegone, Natal Nerímio [UNESP]Casademont, ChristopheArurault, Laurent2023-03-01T20:09:51Z2023-03-01T20:09:51Z2022-09-01info:eu-repo/semantics/publishedVersioninfo:eu-repo/semantics/articlehttp://dx.doi.org/10.1016/j.matchemphys.2022.126369Materials Chemistry and Physics, v. 288.0254-0584http://hdl.handle.net/11449/24028210.1016/j.matchemphys.2022.1263692-s2.0-85132329091Scopusreponame:Repositório Institucional da UNESPinstname:Universidade Estadual Paulista (UNESP)instacron:UNESPengMaterials Chemistry and Physicsinfo:eu-repo/semantics/openAccess2023-03-01T20:09:51Zoai:repositorio.unesp.br:11449/240282Repositório InstitucionalPUBhttp://repositorio.unesp.br/oai/requestopendoar:29462024-08-05T21:20:16.602382Repositório Institucional da UNESP - Universidade Estadual Paulista (UNESP)false |
dc.title.none.fl_str_mv |
Influence of the anodization electrical mode on the final properties of electrocolored and sealed anodic films prepared on 1050 aluminum alloy |
title |
Influence of the anodization electrical mode on the final properties of electrocolored and sealed anodic films prepared on 1050 aluminum alloy |
spellingShingle |
Influence of the anodization electrical mode on the final properties of electrocolored and sealed anodic films prepared on 1050 aluminum alloy Regone, Natal Nerímio [UNESP] Aluminum Anodization Electrocoloring Galvanostatic mode Potentiostatic mode |
title_short |
Influence of the anodization electrical mode on the final properties of electrocolored and sealed anodic films prepared on 1050 aluminum alloy |
title_full |
Influence of the anodization electrical mode on the final properties of electrocolored and sealed anodic films prepared on 1050 aluminum alloy |
title_fullStr |
Influence of the anodization electrical mode on the final properties of electrocolored and sealed anodic films prepared on 1050 aluminum alloy |
title_full_unstemmed |
Influence of the anodization electrical mode on the final properties of electrocolored and sealed anodic films prepared on 1050 aluminum alloy |
title_sort |
Influence of the anodization electrical mode on the final properties of electrocolored and sealed anodic films prepared on 1050 aluminum alloy |
author |
Regone, Natal Nerímio [UNESP] |
author_facet |
Regone, Natal Nerímio [UNESP] Casademont, Christophe Arurault, Laurent |
author_role |
author |
author2 |
Casademont, Christophe Arurault, Laurent |
author2_role |
author author |
dc.contributor.none.fl_str_mv |
Universidade Estadual Paulista (UNESP) Bât. CIRIMAT |
dc.contributor.author.fl_str_mv |
Regone, Natal Nerímio [UNESP] Casademont, Christophe Arurault, Laurent |
dc.subject.por.fl_str_mv |
Aluminum Anodization Electrocoloring Galvanostatic mode Potentiostatic mode |
topic |
Aluminum Anodization Electrocoloring Galvanostatic mode Potentiostatic mode |
description |
The present study focused on the preparation of colored coatings on 1050 aluminum substrate using a four-step process including pretreatments, anodization, electrocoloring and hydrothermal sealing. Anodization of aluminum susbtrates can be usually performed either in potentiostatic mode or galvanostatic mode. The aim here was to study the influence of the electrical anodization mode (ideally with similar film thicknesses) and the influence of the alternating voltage applied during subsequent coloring on the final coating properties (color, hardness and anti-corrosion performance). Scanning electron microscopies (SEM and FEG-SEM) were used to obtain surface and cross-sectional views of the final coatings, and estimate the average pore diameter, while layer thicknesses (i.e. barrier, porous and sealing layers) were evaluated using different analytical techniques. Final coatings properties (i.e. hardness, color, electrical and corrosion resistance) were then studied. In particular, corrosion resistance was analyzed by electrochemical impedance spectroscopy (EIS) and potentiodynamic polarization. For both electrical anodization modes, similar coating thicknesses were obtained experimentally, while average pore diameter of the anodic films were of the same order of magnitude. For each electrical anodization mode, deeper color was obtained for optimum coloring voltage. However, the deeper colors obtained were associated with the lower coating hardness. Furthermore, based on total resistance values, coatings resulting from galvanostatic anodization have enhanced corrosion resistance than samples prepared by potentiostatic anodization. However, EIS analysis agreed with the results shown by polarization curves, highlighting that in such experimental conditions, coloring using high alternating voltage can be detrimental to the anticorrosion properties of such coatings. |
publishDate |
2022 |
dc.date.none.fl_str_mv |
2022-09-01 2023-03-01T20:09:51Z 2023-03-01T20:09:51Z |
dc.type.status.fl_str_mv |
info:eu-repo/semantics/publishedVersion |
dc.type.driver.fl_str_mv |
info:eu-repo/semantics/article |
format |
article |
status_str |
publishedVersion |
dc.identifier.uri.fl_str_mv |
http://dx.doi.org/10.1016/j.matchemphys.2022.126369 Materials Chemistry and Physics, v. 288. 0254-0584 http://hdl.handle.net/11449/240282 10.1016/j.matchemphys.2022.126369 2-s2.0-85132329091 |
url |
http://dx.doi.org/10.1016/j.matchemphys.2022.126369 http://hdl.handle.net/11449/240282 |
identifier_str_mv |
Materials Chemistry and Physics, v. 288. 0254-0584 10.1016/j.matchemphys.2022.126369 2-s2.0-85132329091 |
dc.language.iso.fl_str_mv |
eng |
language |
eng |
dc.relation.none.fl_str_mv |
Materials Chemistry and Physics |
dc.rights.driver.fl_str_mv |
info:eu-repo/semantics/openAccess |
eu_rights_str_mv |
openAccess |
dc.source.none.fl_str_mv |
Scopus reponame:Repositório Institucional da UNESP instname:Universidade Estadual Paulista (UNESP) instacron:UNESP |
instname_str |
Universidade Estadual Paulista (UNESP) |
instacron_str |
UNESP |
institution |
UNESP |
reponame_str |
Repositório Institucional da UNESP |
collection |
Repositório Institucional da UNESP |
repository.name.fl_str_mv |
Repositório Institucional da UNESP - Universidade Estadual Paulista (UNESP) |
repository.mail.fl_str_mv |
|
_version_ |
1808129311013601280 |