Marginal fit at cylinder-abutment interface before and after overcasting procedure

Detalhes bibliográficos
Autor(a) principal: Moraes,Luciana Martins Cres
Data de Publicação: 2005
Outros Autores: Rossetti,Paulo Henrique Orlato, Rossetti,Leylha Maria Nunes, Pedreira,Ana Paula Ribeiro do Vale, Valle,Accacio Lins do, Bonachela,Wellington Cardoso
Tipo de documento: Artigo
Idioma: eng
Título da fonte: Journal of applied oral science (Online)
Texto Completo: http://old.scielo.br/scielo.php?script=sci_arttext&pid=S1678-77572005000400010
Resumo: The aim of this study was to measure marginal fit at cylinder-abutment interface, before and after overcasting procedure. A hexagonal implant was fixed to a stainless steel base and a Estheticone-like abutment used during all the experiment. Before casting procedure, gold (Group I) and Ni-Cr-Be (Group II) premachined cylinders were tightened to the abutment with gold and titanium screws (in both groups), with 10Ncm and 20Ncm torque values for the same screw type. Vertical measures were taken at the light microscope (Mitutoyo 5050, Tokyo, Japan) three times in six different parts along the abutment-cylinder interface for each torque value. Cylinders were overcast with Ag-Pd (Group I) or Ni-Cr-Be (Group II) alloy. After casting, the same measures and torque values were repeated. Intragroup differences (10 or 20Ncm torque values, before and after casting) and intergroup differences (10 and 20Ncm torque values, before or after casting) were analyzed by the Paired t Test; (p<0.05). Intragroup differences were observed for G-I (gold, 20Ncm, titanium screw, p=0.044) and for G-II (Ni-Cr-Be, 10Ncm, gold screw, p=0.002). Intergroup differences only were not observed in the G-II group (Ni-Cr-Be, 10 and 20Ncm, titanium screw, p=0.534). Within the limits of this study, the following conclusions can be drawn: 1) Regardless of screw type, marginal misfit was higher for Ni-Cr-Be cylinders after casting, but within acceptable levels of fit; 2) The combination of gold cylinders with gold or titanium screws was the most effective to reduce marginal misfit; 3) Both screw types did not improve marginal fit of Ni-Cr-Be cylinders after overcastting, and 4) Although a 20Ncm torque improved marginal fit in all situations, its use is not recommended due to the increased risk of prosthesis failure. Ni-Cr-Be alloys may be successfully used in single-tooth implant restorations, with no damage to the fit between abutment and prosthetic cylinder.
id USP-17_e6525554037d1b7627a9082d8eaa05ca
oai_identifier_str oai:scielo:S1678-77572005000400010
network_acronym_str USP-17
network_name_str Journal of applied oral science (Online)
repository_id_str
spelling Marginal fit at cylinder-abutment interface before and after overcasting procedureMarginal fitProsthetic cylinderDental alloysCastingDental implantsThe aim of this study was to measure marginal fit at cylinder-abutment interface, before and after overcasting procedure. A hexagonal implant was fixed to a stainless steel base and a Estheticone-like abutment used during all the experiment. Before casting procedure, gold (Group I) and Ni-Cr-Be (Group II) premachined cylinders were tightened to the abutment with gold and titanium screws (in both groups), with 10Ncm and 20Ncm torque values for the same screw type. Vertical measures were taken at the light microscope (Mitutoyo 5050, Tokyo, Japan) three times in six different parts along the abutment-cylinder interface for each torque value. Cylinders were overcast with Ag-Pd (Group I) or Ni-Cr-Be (Group II) alloy. After casting, the same measures and torque values were repeated. Intragroup differences (10 or 20Ncm torque values, before and after casting) and intergroup differences (10 and 20Ncm torque values, before or after casting) were analyzed by the Paired t Test; (p<0.05). Intragroup differences were observed for G-I (gold, 20Ncm, titanium screw, p=0.044) and for G-II (Ni-Cr-Be, 10Ncm, gold screw, p=0.002). Intergroup differences only were not observed in the G-II group (Ni-Cr-Be, 10 and 20Ncm, titanium screw, p=0.534). Within the limits of this study, the following conclusions can be drawn: 1) Regardless of screw type, marginal misfit was higher for Ni-Cr-Be cylinders after casting, but within acceptable levels of fit; 2) The combination of gold cylinders with gold or titanium screws was the most effective to reduce marginal misfit; 3) Both screw types did not improve marginal fit of Ni-Cr-Be cylinders after overcastting, and 4) Although a 20Ncm torque improved marginal fit in all situations, its use is not recommended due to the increased risk of prosthesis failure. Ni-Cr-Be alloys may be successfully used in single-tooth implant restorations, with no damage to the fit between abutment and prosthetic cylinder.Faculdade De Odontologia De Bauru - USP2005-12-01info:eu-repo/semantics/articleinfo:eu-repo/semantics/publishedVersiontext/htmlhttp://old.scielo.br/scielo.php?script=sci_arttext&pid=S1678-77572005000400010Journal of Applied Oral Science v.13 n.4 2005reponame:Journal of applied oral science (Online)instname:Universidade de São Paulo (USP)instacron:USP10.1590/S1678-77572005000400010info:eu-repo/semantics/openAccessMoraes,Luciana Martins CresRossetti,Paulo Henrique OrlatoRossetti,Leylha Maria NunesPedreira,Ana Paula Ribeiro do ValeValle,Accacio Lins doBonachela,Wellington Cardosoeng2006-01-20T00:00:00Zoai:scielo:S1678-77572005000400010Revistahttp://www.scielo.br/jaosPUBhttps://old.scielo.br/oai/scielo-oai.php||jaos@usp.br1678-77651678-7757opendoar:2006-01-20T00:00Journal of applied oral science (Online) - Universidade de São Paulo (USP)false
dc.title.none.fl_str_mv Marginal fit at cylinder-abutment interface before and after overcasting procedure
title Marginal fit at cylinder-abutment interface before and after overcasting procedure
spellingShingle Marginal fit at cylinder-abutment interface before and after overcasting procedure
Moraes,Luciana Martins Cres
Marginal fit
Prosthetic cylinder
Dental alloys
Casting
Dental implants
title_short Marginal fit at cylinder-abutment interface before and after overcasting procedure
title_full Marginal fit at cylinder-abutment interface before and after overcasting procedure
title_fullStr Marginal fit at cylinder-abutment interface before and after overcasting procedure
title_full_unstemmed Marginal fit at cylinder-abutment interface before and after overcasting procedure
title_sort Marginal fit at cylinder-abutment interface before and after overcasting procedure
author Moraes,Luciana Martins Cres
author_facet Moraes,Luciana Martins Cres
Rossetti,Paulo Henrique Orlato
Rossetti,Leylha Maria Nunes
Pedreira,Ana Paula Ribeiro do Vale
Valle,Accacio Lins do
Bonachela,Wellington Cardoso
author_role author
author2 Rossetti,Paulo Henrique Orlato
Rossetti,Leylha Maria Nunes
Pedreira,Ana Paula Ribeiro do Vale
Valle,Accacio Lins do
Bonachela,Wellington Cardoso
author2_role author
author
author
author
author
dc.contributor.author.fl_str_mv Moraes,Luciana Martins Cres
Rossetti,Paulo Henrique Orlato
Rossetti,Leylha Maria Nunes
Pedreira,Ana Paula Ribeiro do Vale
Valle,Accacio Lins do
Bonachela,Wellington Cardoso
dc.subject.por.fl_str_mv Marginal fit
Prosthetic cylinder
Dental alloys
Casting
Dental implants
topic Marginal fit
Prosthetic cylinder
Dental alloys
Casting
Dental implants
description The aim of this study was to measure marginal fit at cylinder-abutment interface, before and after overcasting procedure. A hexagonal implant was fixed to a stainless steel base and a Estheticone-like abutment used during all the experiment. Before casting procedure, gold (Group I) and Ni-Cr-Be (Group II) premachined cylinders were tightened to the abutment with gold and titanium screws (in both groups), with 10Ncm and 20Ncm torque values for the same screw type. Vertical measures were taken at the light microscope (Mitutoyo 5050, Tokyo, Japan) three times in six different parts along the abutment-cylinder interface for each torque value. Cylinders were overcast with Ag-Pd (Group I) or Ni-Cr-Be (Group II) alloy. After casting, the same measures and torque values were repeated. Intragroup differences (10 or 20Ncm torque values, before and after casting) and intergroup differences (10 and 20Ncm torque values, before or after casting) were analyzed by the Paired t Test; (p<0.05). Intragroup differences were observed for G-I (gold, 20Ncm, titanium screw, p=0.044) and for G-II (Ni-Cr-Be, 10Ncm, gold screw, p=0.002). Intergroup differences only were not observed in the G-II group (Ni-Cr-Be, 10 and 20Ncm, titanium screw, p=0.534). Within the limits of this study, the following conclusions can be drawn: 1) Regardless of screw type, marginal misfit was higher for Ni-Cr-Be cylinders after casting, but within acceptable levels of fit; 2) The combination of gold cylinders with gold or titanium screws was the most effective to reduce marginal misfit; 3) Both screw types did not improve marginal fit of Ni-Cr-Be cylinders after overcastting, and 4) Although a 20Ncm torque improved marginal fit in all situations, its use is not recommended due to the increased risk of prosthesis failure. Ni-Cr-Be alloys may be successfully used in single-tooth implant restorations, with no damage to the fit between abutment and prosthetic cylinder.
publishDate 2005
dc.date.none.fl_str_mv 2005-12-01
dc.type.driver.fl_str_mv info:eu-repo/semantics/article
dc.type.status.fl_str_mv info:eu-repo/semantics/publishedVersion
format article
status_str publishedVersion
dc.identifier.uri.fl_str_mv http://old.scielo.br/scielo.php?script=sci_arttext&pid=S1678-77572005000400010
url http://old.scielo.br/scielo.php?script=sci_arttext&pid=S1678-77572005000400010
dc.language.iso.fl_str_mv eng
language eng
dc.relation.none.fl_str_mv 10.1590/S1678-77572005000400010
dc.rights.driver.fl_str_mv info:eu-repo/semantics/openAccess
eu_rights_str_mv openAccess
dc.format.none.fl_str_mv text/html
dc.publisher.none.fl_str_mv Faculdade De Odontologia De Bauru - USP
publisher.none.fl_str_mv Faculdade De Odontologia De Bauru - USP
dc.source.none.fl_str_mv Journal of Applied Oral Science v.13 n.4 2005
reponame:Journal of applied oral science (Online)
instname:Universidade de São Paulo (USP)
instacron:USP
instname_str Universidade de São Paulo (USP)
instacron_str USP
institution USP
reponame_str Journal of applied oral science (Online)
collection Journal of applied oral science (Online)
repository.name.fl_str_mv Journal of applied oral science (Online) - Universidade de São Paulo (USP)
repository.mail.fl_str_mv ||jaos@usp.br
_version_ 1748936433943445504